What is the height difference reading on the U-Tube? What is the height difference reading on the U-Tube? *1. Consider a low speed subronic wind tunnel with acontractionorea ratio for the nozzle. If the flow in the test section is atstondard seo level conditions with a velocity of 30 meters per rec,Calculate the height difference in a u- tube mercury manometer withone side connected to the nozzle iniet and the other to the test19/m3section. Png= 1.36 x100.34 m0.39 m0.21 m0.05 m0.22 m0.11 m

Given:Contraction area ratio, A1A2=121Density of mercury, ρHg=1.36×103 kg/m3velocity, v=30 m/s

What is the height difference reading on the U-Tube? * 1. Consider a low speed subsonic wind funnel with a %, contraction. area ratio for the nozzle. If the flow in the test section is at a stondard seo level conditions with a velocity of 30 meterN per vec, Calculate the height difference in a U-tube mercury manometer with one side connected to the nozzle inlet and the other to the test

What is the height difference reading on the U-Tube? * 1. Consider a low speed subsonic wind funnel with a %, contraction. area ratio for the nozzle. If the flow in the test section is at a stondard seo level conditions with a velocity of 30 meterN per vec, Calculate the height difference in a U-tube mercury manometer with one side connected to the nozzle inlet and the other to the test

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q3/Answer the flowing 1. when ( a) M 1 (c) M =1 , the flow is accelerates if the cross sectional area is increases 2. If the sonic conditions does occur in the duct it will occur at the duct maximum area(T/F) 3. For laminar zone the velocity profile will be (a) Linear (b) (b) Parabolic (c) (c) Logarithmic (d) (d)none of above 4. The thickness of boundary layer decreases as distance from leading edge increase(T/F) 5. The main property that effects a boundary layer is... (a) Temperature (b) pressure (c) viscosity (d) surface tention.
Simulation of laminar gas flow in the pipe with Ansys Fluent Task: 1. Calculate velocity distribution in y axis at inlet and outlet of the pipe. Submit it as a chart. 2. Calculate velocity distribution over the pipe length. Submit it as a chart. Figure. pipe geometry L, m = 16 R, m= 0.15 Inlet velocity, m/s= 0.08 Gas= Oxygen Need proper solution like pdf file, don't need steps by steps. If you can can do it through ansys fluent. Write proper solution on word file or pdf.
A bicycle tire is fi lled with air at an absolute pressure of169.12 kPa, and the temperature inside is 30.0 °C. Supposethe valve breaks, and the air starts to exhaust out of the tireinto the atmosphere (pa = 100 kPa absolute and Ta =20.0 °C). The valve exit is 2.00 mm in diameter and is thesmallest cross-sectional area of the entire system. Frictionallosses can be ignored here; one-dimensional isentropicflow is a reasonable assumption. (a) Find the Machnumber, velocity, and temperature at the exit plane of thevalve (initially). (b) Find the initial mass flow rate out ofthe tire. (c) Estimate the velocity at the exit plane using theincompressible Bernoulli equation. How well does thisestimate agree with the “exact” answer of part (a)? Explain.
Calculate the available net positive section head NPSH in a pumping system if the liquid density p 1200 kg/m'. The liquid dynamic viscosity u 0.4 Pa.s, the mean velocity a= 1 m/s, the static head on the suction side z = 3m, the inside pipe diameter di, = 0.0526m. the gravitational acceleration g = 9.81 m/s, and the equivalent length on the suction side EL, = 5.0 m. The liquid is at its normal boiling point. Neglect entrance and exit 1 losses.
A 5-mm-diameter capillary tube is used as a viscometer foroils. When the flow rate is 0.071 m3/h, the measured pressuredrop per unit length is 375 kPa/m. Estimate the viscosityof the fluid. Is the flow laminar? Can you also estimate thedensity of the fluid?
Take the densilty and pressure values at 7km, and then apply Bernoulli equation. I think this is the method to solve the problem,If there any you can proceed with that. Please do it fast ,Very urgent. Question 1: . Consider an airplane flying at a standard altitude of 7 km with a velocity of 300 m/s. At a point on the wing of the airplane, the velocity is 400 m/s. Calculate the pressure at this point.
Find the Base Temp at Airflow=0.1 m/s. it's an exponential relation. will upvote if correct.
338 B/s O 1: 56% E 3:01 Question: Gasoline is flowing through this 180° pipe bend. The pipe cross-sectional area is 18 in?. Take the pipe weight as 5 Kg. Flow rate is 0.5 liters/s. Pressure at section-1 6 psia, pressure at section-2 is 4 psia. Calculate the anchoring force required to hold this pipe and also show its direction, referenced to proper 2-dimensional a cartesian coordinate system. (2 1
An incompressible fluid (kinematic viscosity, 7.4 x10-7 m²/s, specific gravity, 0.88) is held between two parallel plates. If the top plate is moved with a velocity of 0.5 m/s while the bottom one is held stationary, the fluid attains a linear velocity profile in the gap of 0.5 mm between these plates; the shear stress in Pascals on the surface of top plate is rt of this book may be repro
Reynold's number of 11090 is obtained for a certain value opening in a shut off valve experimentjexercise 1), when water flows through a pipe of diameter 23 mm. The viscosity of water is 1.14 x10-Nm Find the velocity of flow for this valve opening in m/s=
For a certain value opening in a shut off valve experiment(exercise 1), the water with a velocity of 0.65 m/s passes through a the pipe of diameter 24 mm. Viscosity of water is 1.14 x10-3Ns/m². Find Reynold's number for this valve opening=
A pipe of diameter 12 cm, is used to pump the water to the house in the Hamra hill at the height of 60 m than the ground. The discharge at the end of the pipe is 200 lit/s. The pressure gauge is fitted at the entry of the pipe in the ground is 34 N/cm?. Find the following: (i) The velocity head at the entry of pipe (in m) (ii) Pressure head at the inlet (in m) (iii) Total available energy per unit weight of the water at the pipe inlet (unit in m) (Enter only the values by referring to the units given in brackets & DO NOT write the unit & do not send the handwritten answers to my mail id...) velocity head at the entry of the pipe is = (unit in m) pressure head at inlet = (unit in m) Total available energy per unit weight of the water at inlet of the pipe