Gasoline is flowing through this 180° pipe bend. The pipe cross-sectional area is 18 in?. Take the pipe weight as 5 Kg. Flow rate is 0.5 liters/s. Pressure at section-16 psia, pressure at section-2 is 4 psia. Calculate the anchoring force required to hold this pipe and also show its direction, referenced to proper 2-dimensional a cartesian coordinate system. 2 1

Gasoline is flowing through this 180° pipe bend. The pipe cross-sectional area is 18 in?. Take the pipe weight as 5 Kg. Flow rate is 0.5 liters/s. Pressure at section-16 psia, pressure at section-2 is 4 psia. Calculate the anchoring force required to hold this pipe and also show its direction, referenced to proper 2-dimensional a cartesian coordinate system. 2 1

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Simulation of laminar gas flow in the pipe with Ansys Fluent Task: 1. Calculate velocity distribution in y axis at inlet and outlet of the pipe. Submit it as a chart. 2. Calculate velocity distribution over the pipe length. Submit it as a chart. Figure. pipe geometry L, m = 16 R, m= 0.15 Inlet velocity, m/s= 0.08 Gas= Oxygen Need proper solution like pdf file, don't need steps by steps. If you can can do it through ansys fluent. Write proper solution on word file or pdf.
Q3/ Water is flowing upwards in an inclined homogeneous pipe from point No. (1) to point No. (2). The following data is available:- 1- Length of pipe, L= 1400 (m). 2- Diameter of pipe, d= 0.25 (m). 3- Elevation of point No. (1) is 15 (m) above the Reference line and elevation of point No. (2) is 30 (m) above the Reference line. 4- Piezometric head at point No. (1), hi= 61.16 ( m of water height). 5- Piezometric head at point No. (2), h2= 20.39 (m of water height). 6- Friction coefficient f=0.02 and hL=zero Find: 1- Head loss of water flow in the pipe from point No.(1) to point No.(2) due to friction hf. 2- Water flow rate Q and flow velocity v in the pipe. Draw the H.G.L. of water flow in the pipe from point No. (1) to point No. (2).
At a point in a pipe that lay flat ノ water in the pipe flows at a speed of 9.0 mls and has 6-40x 104 Pa a gaoge pressure is Find the gauge pressure at point 2 of pipe that lower than the first point 8.0 m and the cvoss - se ctional| area of the pipe is double of first point . Answer [1.52x105 Pa]
A 9.8 m A fluid of relative density 0.88 is flowing through a pipe constant diameter of 15 mm (see the Figure). The pressure at A is 150 kPa and the pressure at B is 225 kPa. The elevation between points A and B is 9.8 m. Calculate the friction loss of the fluid (in meters), (provide your answer with four decimal points) P Type here to search O 10°C Sunny AQA ENG 0029 16/02/2022 DELL priSc FS F6 5 E R J K L %23 F E Aock C V sage page VO at gr ctri
The pipe flow in figure is driven by pressurized air in the tank. What gage pressure (P1) is needed to provide a water flow rate (60 m/h) take (v = 1.15*10 m2/sec).If the (P1 =700Kpa) and the fluid specific gravity is (0.68).estimate the viscosity of the fluid if the flow rate is ( 27 m/sec). 30 m Smoxoth pipe: d = 5 cn Open jet 80 m 10 m - 60 m 86
1) The velocity profile of a viscus fluid over a plate is parabolie with vertex 25 em from the plate ,where the velocity 125 cm/s. calculate the velocity gradient and shear stress at distance of (0, 5, 15 and 25 cm) from the plate given the viscosity of the fluid =7 poise ? Also draw the figure explain the relationship between the velocity gradient and shear stress. Take velocity profile for parabolic equation, (v = ay + by + c)
/ A fluid containing (water, oil, air) flowing through the tube and open to the atmosphere as shown in the figure below. Note that p° = 1.013*10 Pa absolute pressure (Pa) = 98111 pa Calculate the height of the air pressure (h2). Density: Pwater = 1000 kg/m³ Poil = 800 kg/m³ Pair = 29 kg/m³ %3D %3D ha=50 hs =50 cm. Com Pa oIL hi =30 cm %3! water he=? air
An incompressible fluid (kinematic viscosity, 7.4 x10-7 m²/s, specific gravity, 0.88) is held between two parallel plates. If the top plate is moved with a velocity of 0.5 m/s while the bottom one is held stationary, the fluid attains a linear velocity profile in the gap of 0.5 mm between these plates; the shear stress in Pascals on the surface of top plate is rt of this book may be repro
Answer with True or False of the following question: (7M 1. Water flows steadily down a vertical pipe of constant cross section. Neglecting friction, according to Bernoulli's equation, velocity decreases with height. 2. A liquid in an open right circular cylinder is given rigid body rotation about the axis of the cylinder. The pressure distribution in any vertical plane is uniform. 3. A curved surface is submerged in a static liquid. The horizontal component of pressure force on it is equal to the pressure force on a vertical projection of the surface. 4. A U-tube manometer measures the difference in total energy between two points.
For the pipe-flow reducing section of the figure shown, D₁ = 8 cm, D₂ = 5 cm, and p=1 atm. All fluids are at 20°C. If V₁ = 5 m/s and the manometer reading is h=58 cm, estimate the total horizontal force resisted by the flange bolts. A 15 Ibinabs Water Open jet This question is designed to help you achieve Learning Outcome 4
Q2/ A fluid containing (water, oil, sand) flowing through the tube and open to the atmosphere as shown in the figure below... Note that p° = 1.013*10$ Pa Calculate the absolute pressure (Pa). Density: Pwater = 1000 kg/m³ Poil = 800 kg/m' Psand = 200 kg/m' %3D h3=12 cm oiL Pa hi=5 cm h2=6 cm !3! →Sand water
Q2/ A fluid containing (water, oil, sand) flowing through the tube and open to the atmosphere as shown in the figure below.. Note that p°- 1.013*105 Pa Calculate the absolute pressure (Pa). Density: Pwater = 1000 kg/m Pail = 800 kg/m Pand = 200 kg/m P. h3=12 cm hg al2cm oIL Pa h25 cm ng = 6 cm %3D Sand water