Please solve this 2 questions What is the error in the FBD routine below?Integer1Integer2123411 00016578SourceASourceBADD_01ADDAddBOR_01BORBoolean OrIn1In2In3In4Dest DOut143.0OutputRegisterMUL_01MULMultiplyEnablelnSourceASourceBd. The ADD_01 block should have assume data available indicator at its inpute. The MUL_01 block should have assume data available indicator at its inputO a. The lines between the BOR_01 block and the MUL_01 block should be a solid lineO b. The line between the MUL_01 block and the OutputRegister2 OREF should be a solid lineO c. None of the choices0.0Dest-OutputRegister2 What is the error in the FBD routine below?Integer1Integer21234e.06578OOSourceASourceBADD_01ADDAddIn1In2In3-In4BOR_01BORBoolean OrDestOut143.0OutputRegisterMUL_01MULMultiply-EnablelnSourceASourceBa. No need for the ADD_01 block to have assume data available indicator at its input Source Ab. The MUL_01 block should have assume data available indicator at its inputO c.No need for the MUL_01 block to have assume data available indicator at its input Source BO d.None of the choicesThe lines between the BOR_01 block and the MUL_01 block should be a solid lineDest D0.0Integer1

According to the question, we need to find the error in the FBD routine below

What is the error in the FBD routine below? Integer1 Integer2 1234 0 O 0 1 65 78 O UU U SourceA SourceB In1 ADD_01 ADD Add BOR_01 BOR Boolean Or In2 In3 In4 Dest Out 143.0 OutputRegister MUL_01 MUL Multiply Enablein SourceA SourceB d. The ADD_01 block should have assume data available indicator at its input e. The MUL_01 block should have assume data available indicator at its input Dest a. The lines between the BOR_01 block and the MUL_01 block should be a solid line O b. The line between the MUL 01 block and the OutputRegister2 OREF should be a solid line Oc. None of the choices 0.0 OutputRegister2

What is the error in the FBD routine below? Integer1 Integer2 1234 0 O 0 1 65 78 O UU U SourceA SourceB In1 ADD_01 ADD Add BOR_01 BOR Boolean Or In2 In3 In4 Dest Out 143.0 OutputRegister MUL_01 MUL Multiply Enablein SourceA SourceB d. The ADD_01 block should have assume data available indicator at its input e. The MUL_01 block should have assume data available indicator at its input Dest a. The lines between the BOR_01 block and the MUL_01 block should be a solid line O b. The line between the MUL 01 block and the OutputRegister2 OREF should be a solid line Oc. None of the choices 0.0 OutputRegister2

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

solve this please
please include full solutions!!! will give thumbs up if answer has complete solution.pleas
NOTE: Solve this as soon as possible, I need this urgently. Determine the currents Iy and I, in the circuit below 6 mA 1.51 1 mA
If IE approximately equal to IC, Calculate R1 in k-ohm.
Only part a and b solve plz
In the circuit shown in the figure below, C=20µF, C2=48µF, C3=33µF, and a voltage Vab-49v is applied accross points a and b. After C is fully charged, the switch is thrown to the right. What is the final voltage on C,? Express your answer in units of V(Volts) using one decimal place. S a C2 C17 C3 b.
Please answer all subpart I will like it please ASAP for like all subpart please... Please sir
Choose the value of the applied Strain in a Strain Gauge, if it causes the resistance to change from 210 ohms to 276 ohms for a gauge factor of 2.3. O a. 0.1366 O b. 0.0027 O c. 1.0062 O d. 0.0144
(b) The circuit in Figure Q2 (b) below shows a rectifier circuit where Vin is a 10kHz sine wave with an amplitude of 2Vpp and RL is 10k. (i) (iii) The componet between A and B is a PN diode, sketch and label its silicon structure and explain its characteristics. Sketch the waveforms you would see at A and B and explain or sketch how you would connect your scope probes to measure them. Label your sketches clearly showing values and axis details. Comment on any similarities or differences between the waveforms at A and B.
QUESTION 1 In the circuit shown, determine the following: a.) The terminal voltage of battery E6 is b (a) 22 (b) 21 (c.) 17 (d) 18 (e) 19 b.) The potential difference, Vge is c V. (a) – 22 (b) 22 (c) - 2 (d) 2 (e) 12 c.) The terminal voltage of battery, E5 is d V (a) 8 (b) 7 (c) 6 (d) 18 (e) 12 d.) The potential difference, Vce is b V. (a) 16 (b) 12 (c) 10 (d) 8 (e) 18 e.) The potential difference, Vdg is e V. (a) 8 (b) – 12 (c) - 8 (d) - 10 (e) 10 a b C 20 E1= 6v, 0.50 E2= 11v, 0.50 E3= 7v, 0.52 = E6= 20v, 0.52 E5= 7v, 0.50 E4= 19v, 0.50 f 20
A. 0.5 A Given the circuit below, find the current /. B. 1A C. 0.75 A in D. 0.6 A 40V 1052 iA
Dopant density (cm-³) 1021 1020 1019 1018 1017 1016 10¹5 1014 1013 10¹2, 10-4 10-3 10-¹ 10⁰ 10¹ 10² 10³ 104 Resistivity (ohm-cm) FIGURE 2-8 Conversion between resistivity and dopant density of silicon at room temperature. (After [3].) N type 10-2 P type EXAMPLE 2-3 Temperature Dependence of Resistance a. What is the resistivity, p, of silicon doped with 10¹7cm-3 of arsenic? b. What is the resistance, R, of a piece of this silicon material 1 um long and 0.1 μm² in cross-sectional area? c. By what factor will R increase (or decrease) from T = 300 K to T = 400 K? d. What As concentration should one choose if she wishes to minimize the change in (c)?