Answered: what is op-amp and its characteristics?

Engineering

Electrical Engineering

what is op-amp and its characteristics?

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Related questions

Q: 10 k2 4 kΩ a b 6 V 4 V Figure Q1

Q: Calculate the the Output Voltage of a non-inverting op-amp with the following parameters Rf =…

A: Features of Op amp High CMRR High gain High input impedence Low output impedence Noise rejection

Q: Operational amplifiers or Op-Amp, has long been used. The early usage of this device were mainly for…

A: An Operational Amplifier is an analog Block which takes input as voltage and produces single ended…

Q: occurs when the input waveform is changing at a rate th ch the op-amp output can change. (In other…

A: Op amps can give output without any distortion if input signal frequency lies with in the specified…

Q: a) What is an Op-Amp, and how is it used? b) What is the equivalent circuit model for an op-amp? c)…

A: a)An operational amplifier, often abbreviated as op-amp, is a type of electronic component primarily…

Q: 6. Consider an operational amplifier with ideal parameters. The op-amp is operated as an inverting…

A: a) We need to draw the circuit diagram of inverting amplifier using ideal operational amplifier with…

Q: 1. Describe some of the characteristics of a practical op-amp. 2. What does a differential amplifier…

A: We are authorized to answer one question at a time, since you have not mentioned which question you…

Q: c) Determine the Common Mode Rejection Ratio (CMRR) and express it in dB for an Op-Amp with an open…

Q: Submit a brief report on 3 different Analog and Digital applications of op-amp and represent a…

A: Analog applications of op amps: Op amp as a summing amplifier: The input voltages are applied to…

Q: c) Design a non-inverting Schmitt trigger circuit with an upper trigger point UTP = 3.1V and lower…

A: Since you have posted multiple different question. we will solve the first question for you. To get…

Q: Given a non inverting op – amp , a) what should be the operating frequency to have a high frequency…

A: (a) Gain(dB) = 100 dB Higher cutoff frequency fH=15 KHz 100=20log AAo=105For 30% lower…

Q: Summarize the differences between passive filter and active filter in terms of gain, cost and…

A: You have asked multiple independent questions. We are authorized to answer one question at a time.…

Q: What does meaning of the symbol plus and minus of the pin-outs of an Op-amp?

A: The representation of the pin-out diagram of an Op-Amp is given below. It comprises of 8 pins in…

Q: V. out ww R, = 2KO R,= 10KO

A: The solution is given below

Q: Discuss current to voltage converter circuit using OP-AMP.

A: Operational Amplifier is direct coupled high gain amplifier. The OP-AMP is multi terminal device.…

Q: Sketch the transfer characteristics of OP-AMP with input offset voltage equal to 4 mV.

A: Let op-amp is ideal, so gain will be infinite input offset voltage Vi/o=±4 mV

Q: Ideal op-amp. What is output voltage.

A: Given circuit is - Given op-amp is ideal.

Q: Power supplies are needed to make operation amplifiers functional. Op-amps can be used with one or…

Q: A voltage follower is to be designed to provide a gain error of less than 0.005 percent. Develop a…

A: Given FGE = 0.005 percent Drawing voltage follower

Q: Design an inverting amplifier to ensure a closed loop gain for the voltage signal of -35

Q: Calculate the maximum efficiency, n for the class B push-pull amplifier shown in Figure Q4(b).…

A: According to the question, for the given class B amplifier as shown below We need to discuss (1)…

Q: Q2: Suggest and draw an mode noise (No simulation needed). Op-amp circuit that reduce the common

Q: 2. How will you convert any op-amp summing amplifier into a voltage averaging amplifier?

A: Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: 4. What is the voltage gain of an inverting op-amp in which the feedback resistor has a value of…

A: Given data, An inverting op-amp in which Rf=7000 ΩRin=1500 Ω

Q: What are the different types of Feedback Amplifiers used in practical applications?

A: Feedback amplifiers are widely used in various practical applications such as audio amplifiers,…

Q: a) Given a non inverting op – amp below, what should be the operating frequency to have a high…

A: (a) Gain(dB)=40 Higher cutoff frequency=20 KHz40=20logAoAo=100For 10% lower gain,A=0.9AoConsidering…

Q: How do we increase the voltage gain of an inverting and non-inverting op amp amplifier?

A: The op amp ideally has a very high gain. It has two terminals for the input, positive and negative…

Q: (a) The BJT and FET are the types of transistor that were used as switches and amplifier in…

A: We are authorized to answer one question at a time, since you have not mentioned which question you…

Q: What is the definition of amplification? How do you go about achieving it?

A: The explanation is as follows.

Q: Describe some of the characteristics of a practical op-amp

A: According to question:

Q: (25 m 1. The value of ... is a measure of noise rejection in the op-amp. 2. Phase shift oscillator…

A: CMRR=20logAdAcm decibels In ideal opamp, it is infinite and we desire to keep this value as high as…

Q: Why OPAMP called operational Amplifier?

A: Op-amp: Op-amp stands for operational amplifier. It is a three terminal device two input and single…

Q: 1. Consider the integrator circuit in Figure QI. The input signal, V, to the circuit is a 100 Hz…

A: Op-Amp can be used in applications like adder and subtractor inside a feedback circuit. An…

Q: 7. The slew rate for an open loop op-amp configuration is 0.66V/us and the input voltage is 10 mV,.…

A: The slew rate for an open-loop op-amp configuration is 0.66 V/μsμs and the input voltage is 10 mVpk.…

Q: ZI The if the input to a Differentiator op-amp is a DC signal then the magnitude of the output will…

A: Given & to find: If the input to a Differentiator op-amp is a DC signal then the magnitude of…

Concept explainers

Operational Amplifier

An operational amplifier also called op amp is an integrated circuit or analog circuit that takes input as a differential voltage and produces output as a single-ended voltage. It is an IC that can amplify weak electric signals.An op amp has one output pin and two input pins. The basic role of an opamp is to amplify the voltage difference between the two input voltages. It is also used in filtering or to perform mathematical operations or in signal conditioning.

Question

what is op-amp and its characteristics?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Introduction

VIEW

Step 2: Characteristics

VIEW

Solution

VIEW

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

III Determine the output voltage of the ideal op - amp differentiator in Figure below for the triangular - wave input shown.
Q-3: Discuss about the cross-over distortion in push-pull class B power amplifier. Draw the proper output waveforms and characteristics showing Flat spot or Dead band. How it can be eliminated?
How the non-inverting amplifier can be useful in practice?
12.11 Identify each of the op-amp configurations below: Ry Vin W out Va o Ry CourseSmart (a) (b) (c)
Compare the classical Op-Amp parameters with modern Op-Amp.
The open loop gain of an op-amp is 92 dB. Given that the open loop corner frequency is 100 Hz, what is the unity gain bandwidth of the op-amp?
One advantage of having feedback in op amp circuit is A.Can control gain B.less complicated C.less input signal D.low gain E.high output voltage F.low bandwidth
B. Design an averaging amplifier based Op-Amp with eight input? and find the output voltage if the input signals are equal with value of 7 Volts?
How would I sketch the input-output relationship of op-amp comparators with hysteresis?
(Write only T or F) 1. An ideal op-amp is usually used in circuits requiring very high accuracy. 2. A practical op-amp can be made ideal by compensation. 3. The output impedance of a good practical op-amp is zero ohms. 4. A voltage follower op-amp is used to prevent circuit loading. 5. The value of the open loop gain of an op-amp determines the overall gain of a differential amplifier. 6. The open loop gain determines the overall gain of an averaging amplifier. 7. If a rectangular pulse is applied to the input of a differentiator, the output is triangular wave. 8. The differentiator can be considered as a low pass filter. 9. The output frequeney of an oscillator depends on the frequeney of the input signal. 10. The overall gain of the oscillator must be more than unity when starting oscillation. 11. An oscillator uses a positive feedback to produce all types of waveforms. 12. Sinusoidal waveforms with fixed frequencies can be produced by Wien-bridge oscillator.
In the experiment (Differential amplifier) answer the following: Theoretical Calculations: 5. Name five other application for op- amp, sketch their circuit and their equations?
A noninverting ampliﬁer is being designed to have a closed-loop gain of 36 dB. What op-amp gain is required to have the gain error less than 0.15 percent?