What are the node voltages at point a, b and c? . Can we get the voltage across resistor R4 using the operating point values? How? Can we get the voltage across resistor R6 using the operating point values? How?

Q: Bimetallic strip could be used as a temperature detector. Explain its working principle and show…

A: Bimetallic thermometer is a device to which can be used to convert a temperature into mechanical…

Q: Copper brushes in D.C. machine are used where low voltage and high currents are involved where high…

A: This is a problem of dc machines. The solution is given in the next step

Q: The purpose of control rods are O a. to shield the area outside of the reactor from radiation O b.…

A: In this question we need to choose a correct option

Q: Explain with reference to the components in the circuit and point P why the warning lamp is on when…

A: To Explain with reference to the components in the circuit and point P why the warning lamp is on…

Q: explain briefly and consicely the importance of tolerance in resistors

A: Tolerance of resistor is the nothing but how much is the resistance value measured of its actual…

Q: A thermistor has a: a. positive output voltage. b. negative output voltage. c .positive…

A: A thermistor is an electronic component that is sensitive to temperature changes and is often used…

Q: QUESTIONS: 1. A transformer is rated at 120V primary/23V secondary. What peak to peak secondary…

A:

Q: 22. a) Describe how the following sensors are used to measure temperature. i) RTD

A: Any system can be autonomous or manual. A system is called autonomous if the output is independent…

Q: The electrical energy that is produced will be a part of the. energy applied to rotate th The number…

A: To fill up the blanks

Q: A platinum resistance temperature detector (RTD) is used to measured temperature of the hot gas. The…

A: We have an RTD (Resistance temperature detector ) which is used to measure temperature of hot gas…

Q: CLO2-A core is wrapped with a 400 nim coil that carries a current of 380 mA. If the reluctance of…

A: Given, A core is wrapped with coil. Number of turns in the coil, N=400. Current in the coil, I=380…

Q: parte A • Develop and explain the electrical schematic for the excitation coil in series. • Develop…

A: It is asked to develop and explain the electrical schematic for the excitation coil in series and in…

Q: What are the advantages of electrodynamic instrument, remind only four

A: given electrodynamic instrument

Q: Which part of CRO produces high fixed velocity electrons? Select one: O a. Vertical Plates O b.…

A: Which part of CRO produces high velocity electrons ?

Q: Find The Currect drawn from the 5 volt Source R,

A:

Q: 9) Does this switch (in the open state) have a Low resistance or a high resistance between its…

A: In this question,  We need to determine and check the resistance low or high as per given the open…

Q: What is the maximum value of the potentiometer? And What project can do using potentiometer? Explain…

A: It is asked to explain in brief about the maximum value of a potentiometer. It is aslo asked in…

Q: In a torsion head type electrodynamometer a current of 25 A requires a deflection of 90° in the head…

A: We have been given an electrodynamometer with, I = 25 and θ = 90° and We have been asked to find,…

Q: In the resistance welding process, select the factor/s that contribute to accomplish coalescence:…

A: Resistance welding: Welding means joint the metals. In resistance welding, the current is applied to…

Q: A 14/2 type NM copper used for a general lighting branch circuit Ampacity : Maximum fuse or circuit…

A: Circuit breaker:- Circuit breakers are used for safety purpose in electrical equipment. It is used…

Q: What minimum value of series resistance s required when three 10-watt, 10-volt, 1000-mA zener diodes…

A: From the Question What minimum value of series resistance is required when three 10-watt, 10-volt,…

Q: 3. Choose the suitable sensor to detect a part inside paper box as shown in Figure 1. Figure 1 a)…

A: The capacitive proximity sensor detects only non ferrous materials with a range of 3mm to 60mm.…

Q: can you explain the operation and need for voltage regulators and tap changers

A: The electrical power system is designed in such a way that its voltage and current supplied to the…

Q: Make a schematic diagram of a light saber

A: It is asked to make schematic of a light saber.

Q: \Answer the following questions 1.Explain briefly the diode and forward bias and reverse bias of it…

A: Disclaimer:  Since you have asked multiple questions, we will solve the first question for you. If…

Q: What are the two types of clipper circuit used in non linear devices?

A: Positive & Negative Clipper Positive Clipper can be used to slice off a portion of the positive…

Q: How to get Multisim to automatically reorganize circuits?

A: Introduction Modularization and reuse are beneficial not only in software development, but also in…

Q: identify any equiptment at home that undergo an electromechanical energy conversion. name and…

A: Electrical machines can be either generator or motors. They can be either Ac machines or DC…

Q: What is the coupling field used between the electrical and mechanical systems in energy conversion…

A: In this case, the proper coupling field that is used between electrical and mechanical systems in…

Q: List out any two advantages of thermistor.

A: Advantages of thermistor: 1. If the temperature of any component in the electrical circuit…

Q: The slight sideward motion of a shaft is called end play. The end play in theshaft of a rotor for an…

A: The end play of the rotor of an electric motor should be,  End play ≤132 inch The given motor has an…

Q: Determine the value of R1 that will ensure proper turn-on and turn-off for the following values: eta…

A:

Q: in the table provided below you have the result of measurement of the platinium resistance…

A:

Q: A precision current shunt is measuring 100 millivolts across it. This indicates a current of 25 A.…

A: Given: Voltage across the current shunt, V=100 mV Current through the current shunt, Ish=25 A