Water is flowing at the rate of 300 L/sec from A to E as shown. Assume f =0.025 for all pipes.Q21500m-300mmQiCDQ6AE600m-300mm(6)400m-450mm300m-450mm600m-250mmQ4600m-200mCompute the flow in Pipe 2, Q2 [in m³/s].none of theseO 0.1582 m3/sO 0.3000 m3/sO 0.0576 m3/sO 0.1006 m3/sO 0.1418 m3/s

Water is flowing at the rate of 300 L/sec from A to E as shown. Assume f = 0.025 for all pipes. 1500m-300mm A Q1 C D E 300m-450mm 600m-250mm 600m-300mm 400m-450mm Q4 600m-200m Compute the flow in Pipe 2, Q2 [in m³/s]. O none of these O 0.1582 m3/s O 0.3000 m3/s O 0.0576 m3/s O 0.1006 m3/s 0.1418 m3/s

Water is flowing at the rate of 300 L/sec from A to E as shown. Assume f = 0.025 for all pipes. 1500m-300mm A Q1 C D E 300m-450mm 600m-250mm 600m-300mm 400m-450mm Q4 600m-200m Compute the flow in Pipe 2, Q2 [in m³/s]. O none of these O 0.1582 m3/s O 0.3000 m3/s O 0.0576 m3/s O 0.1006 m3/s 0.1418 m3/s

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the diameter of steel pipe needed to deliver water (20°C) at a rate of 2 cu. m/s from a reservoir with water surface elevation of 60 m to a reservoir 200 m away with a water surface elevation of 30 m. Assume a squared edge inlet and outlet (k = 1) and no bends in the pipe. Further assume there are two open gate valves in the pipe (k=0.2).
Q2) The network shown in Fig. using Hardy Cross method, find the discharge flow through cach pipe. All data of pipes in table below. Pipe No. AB ВС AC CD AD 100 L/s D(mm) 600 400 200 300 200 L (m) 300 250 250 300 250 30L/s 20 L/s 0.021 0.02 0.022 0.018 0.021 50 L/s
The pump in the figure B. draws water from a reservoir and discharges through 2 V2 inches hose, which terminates in a nozzle having a jet diameter of inch. The head losses are: I to 2. 5.75 ft: 2 to 3. negligible: 3 to 4. 30.61 ft. 4 to 5. 11.6 ft. Compute the required horsepower output of the pump and make a table of the heads at the five points. Q is (a) 261 gpm. (b) 361 gpm.
Water at 100 kPa flowing in a 10-cm-diameter pipe passes through a 2-cm-diameter flow nozzle equipped with a manometer across the nozzle. 10 cm 8 cm S = 10 12 cm S- 13 16.0 Determine the flow of water through the nozzle if coefficient of discharge is 0.7 a.) 1498 mL/s b.) 1433 mL/s c.) 4488 mL/s d.) 4539 mL/s e.)
Q3
Determine the flow distribution of water in the system shown in Figure below. Assume constant friction factors, with f= 0.03. The head-discharge for the pump is Hp = 70 m el 50 m Pipe L (m) D (mm) ΣΚ el 48 m 1 100 750 850 350 200 200 [2] [4] 3 el 0m [5] 4 500 200 350 250 [1] [3]
Please correct answer And solve both part
P10.) Determine the flow in each pipe shown in the figure. Assume f = 0.02 for all pipes. Subject: fluid mechanic Lesson: *Conservation of Energy *Fluid Flow in Pipes
q7