Water flows in a pipe of 1-in. diameter at a temperature of 70°F. The pressure values at points 1 and 2 are found to be 20 psi and 25 psi, respectively. The elevation of point 1 is 12 feet, and the elevation of point 2 is 0 feet. There are 15 feet of pipe between the two points. Determine the direction of flow. flow is from point 1 to point 2 flow is from point 2 to point 1 water does not flow between point 1 and point 2 continued from previous question] Water flows in a pipe of 1-in. diameter at a temperature of 70°F. The pressure values at points 1 and 2 are found to be 20 psi and 25 psi, respectively. The elevation of point 1 is 12 feet, and the elevation of point 2 is O feet. There is 15 feet of pipe between the two points. What is the minimum discharge above which the flow will not be laminar? Report your answer in gallons per minute (gpm) with 2 decimal places,

Water flows in a pipe of 1-in. diameter at a temperature of 70°F. The pressure values at points 1 and 2 are found to be 20 psi and 25 psi, respectively. The elevation of point 1 is 12 feet, and the elevation of point 2 is 0 feet. There are 15 feet of pipe between the two points. Determine the direction of flow. flow is from point 1 to point 2 flow is from point 2 to point 1 water does not flow between point 1 and point 2 continued from previous question] Water flows in a pipe of 1-in. diameter at a temperature of 70°F. The pressure values at points 1 and 2 are found to be 20 psi and 25 psi, respectively. The elevation of point 1 is 12 feet, and the elevation of point 2 is O feet. There is 15 feet of pipe between the two points. What is the minimum discharge above which the flow will not be laminar? Report your answer in gallons per minute (gpm) with 2 decimal places,

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

1. Water flows through Pipe A and into parallel pipes 1,2 and 3, and out through Pipe B. The properties of the pipes are listed as follows: Pipe Length (m) Diameter (cm) 30 Friction Coefficient, f A 1 300 10 0.020 240 600 2 15 0.018 3 20 0.017 В 30 The upstream junction (near A) has an elevation of 90m with a pressure of 205 KPa; the downstream junction is at elevation 30 m. If the average velocity in Pipe A is 3.0 m/s, find the pressure at the downstream junctions and rate of flow in each pipe. Also, draw the pipe system.
ii. Water is flowing through a pipe of 5 cm diameter under a pressure of 29.43 N/cm² (gauge) and at mean velocity of 2.0 m/s. Calculate the total head of the water at a cross-section that is 5 m above the datum line.
A pipe carrying oil (SG = 0.877) change in size from 150mm diameter in point 1 to 450mm diameter in point 2. Point 1 is 3.6m lower than point 2 and the pressure at point 1 is 90KPA while on point 2, the pressure is 60KP.. If the discharge is 150 L/s, determine the head lost and the direction of flow (A Direction cannot be determined B Direction is point 1 to point 2 C) HL = 4.38 m D HL = 7.11 m E HL = 5.13 m (F) HL = 3.51 m G Direction is point 2 to point 1
Water flows from A to E through the pipe system shown. It is known that the flow in pipe BFGC IS 30 LITERS /SEC. and that the pressure head at A is 60 m. Assuming that f =0.022 and that all the pipes are level, determine the total flow from A to E and the pressure heads at B, C, D and E.
ISTINYE ISU UNIVERSITY Question 2: A steel pipe is used to drain water from a reservoir that is 50 m above the datum, and water is discharged into the air at the elevation of the datum. The pipe is 1500 m long and 450 mm diameter and 50 mm wall thickness. A valve is installed at the downstream end of the pipe allows a flow rate of 0.71 m³/s. The valve was completely closed in 1.4 sec. Calculate maximum hammer pressure at the valve. The pipe is longitudinally anchored. Eb = 2.1×10° N/m², E. -1.9×10¹¹ N/m².
a. Determine the velocity of flow in the pipe in m/s. b. Determine the discharge Q in m^3/s. c. How many meters above the center of the pipe will water stand in piezometer tube 3? d.
A cylindrical tank with vertical axis contains water. A 50 mm orifice is located at the side 0.60 m above the bottom of the tank and 1.50 m directly above the orifice is another orifice 75mm diameter. Cv is 0.98 and C is 0.61 for both orifices. Determine the: show complete solution thumbs up guaranteeda. h1 in metersb. Discharge in the lower orifice in lit/secc. Total discharge from the 2 orifices in lit/sec
Prov. in orifice meter with orifice diameter 10 cm is inserted in a pipe of 20 cm diameter. The pressure gauges fitted upstream and downstream of the orifice meter gives readings of 19.62 N/cm2 and 9.81 N/cm2 respectively. Co-efficient of discharge for the meter is given as 0.6. Find the discharge of water through pipe.
Please answer all. I will rate. Points A and B are 5 km apart along a new 60 cm diameter cast iron pipe carrying water. A is 9m higher than B. If the pressure at B is 140 KPa greater than at A. f= 0.019 Determine the head loss in meters. choices: 7.25, 5.27, 2.75, 7.52 Determine the flow rate in lit/sec. choices: 522.88, 822.55, 885.22, 228.55
2. Water flows upward through an inclined pipe (8 = 45°) with diameter of 5 cm. Gauges were attached to the pipe, 12 meters apart following the inclination, to determine pressure between two points which has a result of 100 kPa difference. Determine the flow rate. Assume the flow is laminar. Use = 0.04. Threo rooonuoiro hauo nineg that nharaote lowa
Water flows from a tank with a water surface elevation of 140 ft to another tank 1500 ft away through a 6-inch commercial steel pipe. The downstream tank has a water surface elevation of 115 ft. Find the flow rate in the pipe. The fluid is water at T = 60 degrees. Neglect all minor losses.
water from a reservoir flows at 0.85 m3/s through a rigid pipe 1200 mm diameter and completely stopped by a closure of a valve almost instantly. Bulk modulus of water is 2.20 x 109 N/m2. a) Find the water hammer pressure for sudden closure. b) Find the discharge if water hammer pressure is 700 KPa. c) If the time of closure of valve is 4 sec. and located at 650 mm from the reservoir, find the water hammer pressure at flow rate at 0.85 m3/s.