Warm air is blown over the inner surface of the windshield of an automobile to defrost ice accumulated on the outer surface. The windshield has a thickness of 5 mm and thermal conductivity of 1.4 W/m-K. The outside ambient temperature is -10°C and the convection heat transfer coefficient is 200 W/m2-K, while the ambient temperature inside the automobile is 25°C. Determine the value of the convection heat transfer coefficient for the warm air blowing over the inner surface of the windshield necessary to cause the accumulated ice to begin melting.

Warm air is blown over the inner surface of the windshield of an automobile to defrost ice accumulated on the outer surface. The windshield has a thickness of 5 mm and thermal conductivity of 1.4 W/m-K. The outside ambient temperature is -10°C and the convection heat transfer coefficient is 200 W/m2-K, while the ambient temperature inside the automobile is 25°C. Determine the value of the convection heat transfer coefficient for the warm air blowing over the inner surface of the windshield necessary to cause the accumulated ice to begin melting.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A pipe 30 m long with an outer diameter of 75 mm is used to deliver steam at a rate of 1500 kg / hour. The steam pressure is 198.53 kPa entering the pipe with a quality of 98%. The pipe that needs to be insulated with a thermal conductivity of 0.2 W / (m K) so that the quality of the steam only decreases slightly to 95%. The temperature of the outer surface of the insulation is assumed to be 25 ° C. The conductive of the pipe material and the situation of no pressure drop in the pipe. A. Determine the enthalpy of incoming vapor = Answer kJ / kg. b. Determine the enthalpy of steam that comes out = Answer kJ / kg. c. Determine the change / loss of steam heat along the flow = Answer watt. d. Determine the minimum required insulation thickness = Answer cm.
Consider the composite wall below. The inner side of the wall is subjected to air flow at 430°C with a heat transfer coefficient of 25 W/m² C and the outter side is subjected to air flow at 55°C with heat transfer coefficient of 10 W/m²-C. If KA 150 W/m-C, Kg = 30 W/m-C, Kc = 65 W/m-C, and Kp = 50 W/m-C, and assuming one dimensional heat flow. Find the rate of heat transfer across the wall. Q Inner 10 cm 3 cm B C 8 cm Outer side D 5 cm 3 cm 7 cm
Steam at 280° C flows in a stainless steel pipe (k = 15 W/m⋅K) whose inner and outer diameters are 5 cm and 5.5 cm, respectively. The pipe is covered with 3-cm-thick glass wool insulation (k = 0.038 W/m⋅K). Heat is lost to the surroundings at 5° C by natural convection and radiation, with a combined natural convection and radiation heat transfer coefficient of 22 W/ m2⋅K.Taking the heat transfer coefficient inside the pipe to be 80 W/ m2⋅K.Determine the rate of heat loss from the steam per unit length of the pipe and Determine the temperature decrease between the inner pipe surface and the outer insulation surface.
A pipe carrying hot gasses is insulated with a material having a thermal conductivity of 0.15 W/mK. The average local heat transfer coefficient by convection to the ambient air is 3 W/m K. The critical diameter of the pipe under 35. these conditions is (a) 100 mm (c) 160 mm (b) 130 mm (d) 200 mm
kindly help me with this question. Thank you, I am having a hard time solving this
An electrical wire with 0.4cm in diameter and 2.5m long extends across a room with 15deg C temperature. Heat is generated in the wire as a result of resistance heating, and the surface of the wire is measured to be 162degC. the voltage drop and electric current along the wire is 60V and 1.64 A, respectively. Determine the convection heat transfer coefficient for the heat transfer between the surface of the wire and the room air. Hint, electric power formula. Round your answer to 2 decimal places.
The upper surface of a 50-cm-thick solid brass plate (k=109 W/mK) is being cooled by water with temperature of 10°C. The upper and lower surfaces of the solid plate maintained at constant temperatures of 60°C and 190°C, respectively. Determine the water convection heat transfer coefficient and the water temperature gradient at the upper plate surface. Water Ts.l · Ts.,2
1- Consider a 1 m high and 2 m wide glass window whose thickness is 8 mm and thermal conductivity is k =0.68 W/m°C. Determine the steady rate of heat transfer through this glass window and temperature of its inner surface for a day during which the room is maintained at 22 °C while the temperature of the outdoors is -3 °C. Take convection heat transfer coefficients on the inner and outer surfaces of the window to be h, = 15 W/M2°C and h, = 20W/m°C .r
A pipe in a manufacturing plant is transporting superheated vapor at a mass flow rate of 0.3 kg/s. The pipe is 10 m long, has an inner diameter of 5 cm and pipe wall thickness of 6 mm. The pipe has a thermal conductivity of 17 W/m.K, and the inner pipe surface is at a uniform temperature of 120 °C. The temperature drop between the inlet and the exit of the pipe is 7 °C, and the constant pressure specific heat of vapor is 2190 J/kg.°C. If the air temperature in the manufacturing plant is 25°C, determine the heat transfer coefficient as a result if convection between the outer pipe surface and the surrounding air. T(r) = 120°C Superheated Air, 25°C r2 vapor r1 0.3 kg/s L = 10 m Tin-Tout = 7°C
The heat flux from a wall to air in motion having a heat transfer coefficient of 15 W/m². K and exposed to a temperature difference of 20 °C is www.bilibilitetit O 225 W O 300 W O 250 W O 375 W wwwwww