Can anyone help me with this heat transfer question. Just 7-83 d85°F20 ft/s1.5 kWresistanceheaterFIGURE P7-82E7-83 A 0.4-W cylindrical electronic component with diam-eter 0.3 cm and length 1.8 cm and mounted on a circuit boardis cooled by air flowing across it at a velocity of 240 m/min.If the air temperature is 35°C, determine the surface tempera-ture of the component. For air properties evaluations, assume afilm temperature of 50°C. Is this a good assumption?7-84 Consider a 50-cm-diameter and 95-cm-long hot watertank. The tank is placed on the roof of a house. The waterinside the tank is heated to 80°C by a flat-plate solar collectorduring the day. The tank is then exposed to windy air at 18°C

Given: Q=0.4 W d=0.3 cm L=1.8 cm v=240 m/min air temp=35oC To determine: Surface temperature

Answered: etermine the surface tem

Engineering

Mechanical Engineering

etermine the surface tem

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

ate the average wind velocity. & A 1.8-m-diameter spherical tank of negligible thickness contains iced water at 0°C. Alr a 25°C flows over the tank with a velocity of 7 m/s. Determine the rate of heat transfer to tank and the rate at which ice melts. The heat of fusion of water at 0°C is 333.7 K3RE
Water is entering a heated tube at mass ow rate of 1.2 kg/s. The temperature at the inlet is 20 C and at the outlet is 80 C. Assume the surface temperature of the tube is 100 C. The convection coe cient of the water ow is 28 W=m2 C. The speci c heat and density of water can be assumed to be 4180 J=kg C and 990 kg=m3. What is the rate of heat transfer to water during this proces
b) A 0.4-W cylindrical electronic component shown in Figure Q3b with diameter 0.3 cm and length 1.8 cm is mounted on a circuit board is cooled by air flowing across it at a velocity of 150 m/min and temperature is 40 °C. Take the pressure of air 1 atm and the film temperature to be 50 °C, determine the surface temperature of the component. Resistor 0.4 W D= 0.3 cm Figure Q3b
Oil is flowing through a 50 mm-ID and 55 mm-OD pure iron pipe at 1 m/s. It is being heated by steam outside the pipe and steam film coefficient may be taken as 11 kW/m2°C. At a particular point along the pipe, the oil is at 50°C, its density is 880 kg/m³, its viscosity is 2.1 cP, its thermal conductivity is 0.135 W/m°C and its specific heat is 2.17 J/g°C. What is the overall heat transfer coefficient at this point, based on the inside area of the pipe? If the steam temperature is 130°C, what is the heat flux at this point, based on the outside area of the pipe?
Air at atmospheric pressure enters a heating duct with dimensions of 3 x 6 in. The air enters the 16 ft long duct with a temperature of 32 fahrenheit, and the duct surface is maintained at 150 fahrenheit. If the air exit temperature is to be 68 fahrenheit, what is the air flow, in lb/hr? (answer in whole number) For air, R = 53.342 ft-lbf/lbm-R, k = 0.173 Btu-in/ft2-hr-F, and cp = 0.24 Btu/lbm-
A 20degC water flows to 50cmx60cm flat plate with velocity of 6m/s . The flat plate surface temperature is maintained at 40deg C. The water flows parallel to the 50cm side of the plate. If the kinematic viscosity of water is 78x10-8 m2/s, What is the local heat flux (Q/A) at the end of the plate (k=0.86 W/m deg C, Re=3840000, and Pr=0.7)? Round your answer to 2 decimal places.
What is the physical significant of prandtl number? Question does the value of the prandtl number depend on the type of flow, or the flow geometry? Does the prandtl number of air change with pressure? does it change your temperature?
Air at 10oC enters a 10-cm-diameter and 4-m-long pipe at a rate of 0.035 kg/s. The inner surface of the pipe has a roughness of 0.22 mm, and the pipe is nearly isothermal at 60o Determine the rate of heat transfer to air using the Nusselt number relation given by (a) Eq. 8–66 and (b) Eq. 8–71. Evaluate air properties at a bulk mean temperature of 20oC. Is this a good assumption?
A long 8-cm diameter vertical steam pipe whose external surface temperature is 90oC passes through some open area that is not protected against the wind blows. Determine the rate of heat loss from the pipe per unit length when the air is at 1 atm, 7oC and the wind is blowing across the pipe at a velocity of 50 km/h. From Table A-1: Thermal conductivity, k = 0.0275 W/m oC , viscosity, v = 1.77 x 10-5 m2/s Prandtl no. Pr = 0.71
mperature of nermocouple kg/m³, and an ideal gas 7-94 The components of an electronic system are located in a 1.5-m-long horizontal duct whose cross section is 20 cm x 20 cm. The components in the duct are not allowed to come into direct contact with cooling air, and thus are cooled by air at 30°C flowing over the duct with a velocity of 200 m/min. If the surface temperature of the duct is not to exceed 65°C, determine the total power rating of the electronic devices that can be mounted into the duct. 7-97 flow If the initial is cor evaluate the 0.3 m of the initial cities of the 3D to the transt perform the from 1 to Treat me and the free stream Electronic o determine components inside 9 percent of tion of this 30°C 200 m/min 65°C Air 1.5 m on 20 cm FIGURE P7-94
The upper surface of a 1 mx 1 m ASTM B152 copper plate is being cooled by air at 20°C. The air is flowing parallel over the plate surface at a velocity of 0.1 m/s. The maximum use temperature for the ASTM B152 copper plate is 260°C (ASME Code for Process Piping, ASME B31.3-2014, Table A-1M). Determine the average convection heat transfer rate from the plate surface that is required to keep the plate surface temperature from going higher than the maximum use temperature. It is given that the properties of air at the film temperature of 140°C are (Table A-15) Pr = 0.7041, k= 0.03374 W/m-K, and v= 2.745 x 10-5 m²/s. The average convection heat transfer rate is W.
An average man has abody surface area of 1.8m2 and a skin temperature of 33degrees celcius .The convection heat transfer coefficient for a clothed person walking in still air is expressed as {h,8.6V^0.53}FOR 0.5<v<2m/s,where V is the walking velocityin m/s.Assuming the average surface temperature of the clothed person to be 30degrees celcius, determine the rate of heat loss from an average man walking in still air at 10degrees celcius by convectionat a walking velocity of (a)0.5m/s (b)1.0m/s (c)1.5m/s (d)2.0m/s