Voc= +20VB=100Please analyze the circuit and determine the voltage gain of both (Av,dc = Vc/vb for DC analysis) and(Av,ac = Vo/Vs for AC analysis)where RB = 470K, Rs = 80, Ci = 47 uF, RC = 4.7K, Co = 47 uF, RL = 10K.In addition, find the output equivalent resistance from the Yo terminal (in AC) and the inputequivalent resistance from the Vs terminal (in AC).Hint: the transistor is a Si-based one. You have to write all the calculation details and verbal explanations. You canprepare your answer on papers with hand-written and name & ID on the top right corner of each paper. You can emailyour scanned answer with enough explanatory details of your name, ID, exam title, and question number.You can calculate hie = beta * 26mv / le (mA, dc) and use the hoe as an open circuit.

We will do DC analysis and AC analysis for given circuit , we will find out DC current then ac…

Voc= +20V B=100 Please analyze the circuit and determine the voltage gain of both (Av,dc = Vc/vb for DC analysis) and (Av,ac = Vo/Vs for AC analysis)where RB = 470K, Rs = 80, Ci = 47 uF, RC = 4.7K, Co = 47 uF, RL = 10K. In addition, find the output equivalent resistance from the Vo terminal (in AC) and the input equivalent resistance from the Vs terminal (in AC).

Voc= +20V B=100 Please analyze the circuit and determine the voltage gain of both (Av,dc = Vc/vb for DC analysis) and (Av,ac = Vo/Vs for AC analysis)where RB = 470K, Rs = 80, Ci = 47 uF, RC = 4.7K, Co = 47 uF, RL = 10K. In addition, find the output equivalent resistance from the Vo terminal (in AC) and the input equivalent resistance from the Vs terminal (in AC).

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Using LTSpice, simulate the circuit below, use 2N3904 for the transistor. Part ! DC simulation: Measure VCE and Ic. Use .op for the simulation cmd. Remove all capacitors and input signals first. Part 2 AC simulation: Connect all capacitors now and apply an AC signal at the input with an amplitufe of 1mV and a frequency of 1kHz. Determine the Voltage gain of the circuit by dividing Vo with Vin. Show the output for both the DC and AC analysis. Take a screenshot of the circuit and the output voltages and waveforms. Paste in a word file, write your answers, then save as pdf. 50 kΩ Σ 20 0,5 ΚΩ wwwh 9 Vcc=20 V Ca=1 µF = Cc₂ Cg=50 μF 5.6 kn B=100 Ca IST • 3.3 ΚΩ 5 ΚΩΣ CE
Coonsider the common emitter amplifier shown in figure below. Assume a β of 100, VBE = 0.7V, VT = 25mA and VA = 100V. Draw an equivalent DC model and determine the rπ, transconductance (gm) and ro. Draw an equaivalent AC model using the small-signal model Find an expression for vbe and vo in terms of the input voltage
Vcc=15V Q1: BC237 Rc 3.6kQ or BC238 B=200 VBE(on)=0.7V R1 110KQ Rs Cci 1000 4.7µF Cco 4.7µF R2 ·27kΩ RE 1.2kQ RL 12kΩ Vs Rin Rout Figure 1. Common-emitter amplifier. 2)
For the circult shown in the given figure. Rc-2.4 k0, Rg-10 ko. Pmin-50, and Vcc=5 V. Determine the range of values of Vgg 50 Ic that the transistor is in saturation. Assume Vy-0.6 V and VCEsat -0.2 V. The range of values of VB8 Is VBB> 12 V Ra VAR со Va VCE OE RC Ncc
For the BJT circuit shown below, sketch the hybrid equivalent model circuit with labels of voltages, impedances, and currents. ... 1.8k0 Vo 39ka 22ko tuF-POL 10UF-POL 1200 1uF-POL 2N2221 100mv 1.5KHZ ODeg
Using LTSpice, simulate the circuit below, use 2N3904 for the transistor. Connect the circuit and apply an AC signal at the input with an amplitude of 1mV and a frequency of 1kHz. Determine the Voltage gain of the circuit by dividing Vo with Vin.
For the circuit of Figure 2. Carry out the analysis in DC and small signal with www.w www www.www Vt=0.7 V, Kn(W/L) = 4 mA/V. Ignore the Early effect. Determine: (a) The current in DC ID. (b) The gains vo/v₁, io/ii (c) The input resistance Rin and output resistance Rout. wwwwww 06402 www Ca HH {ama Ο ΜΩ www.11 Figura 2: 0.51 k www.li 12 V • 27 ΚΩ Ca +1₁ -0% 4.7 k
........ (Figure-1) R. RB= 380kN,Rc= 1kN B = 100, VBB = Vcc=12V RB ww Vec CC ......... I, V CE СЕ V ВЕ BB Q-1-b) Describe briefly the input / output characteristics and application of Common Emitter BJT Configuration
. Design a fixed bias-transistor circuit using V = Vcc = 10 V for a Q-point of Iç = 5 mA and Va 4 V. Assume Boc = 100.The design involves finding R, and Rc. inakomeont thot one is hiased
Determine the input resistance Rin as indicated in the figure. Ignore resistor ro of the transistor and capacitors are large. A. Rin = R1//R2//R3 B. Rin = R2//R3 (//R4//R5) C. Rin = R2//R3 // ( r π + [1+gm r π ] (//R4//R5) ) D. Rin = R2//R3 // r π (//R4//R5) )
Q1. The output characteristic of a typical transistor is shown below, where the quiescent point is selected on it. This transistor is used in the bias circuit presented below. Find the suitable values of Rg and Rc to fix the Q-point of the circuit properly. +Vcc = 12 V 12- Is = 70 uA 10- Ig = 60 uA 8- Rc Is = 50 uA Rs 6- Ig= 40 uA 4. Is = 30 uĄ Is = 20 uA B = 100 2- VBE = 0.7 V 0- -2- 2 4 6 8 10 12 14 16 VCE (V) Ic (mA)
Perform DC analysis, mathematically & graphically of figure 5.VDD=10V,VGG=1V, RD=2KQ,RG=1MN, IDSS = 8mA, Vp = -8V, %3D C2=1uf. Draw the load line on the transfer curve? b) How would the DC load line shift if VGG = OV? Draw the load line on the transfer curve? +Vpp Rp RG VGG