iv. For six-phase half-wave rectifier circuit, the preferred circuit from the point ofharmonics reduction in the supply currents is:(a) Simple six-phase half-wave circuit.(b)Double-star six-phase half-wave circuit.(c) Six-phase fork connection circuit.v. The DC supply of single phase bridge inverter is 350V. For quasi-square waveoutput voltage with a 70 percent ON time and frequency is 50HZ, the RMS valueof output voltage is:(a) 292.8V(b) 220.5V(c) 250.6V

Answered: Image /qna-images/answer/ba9c3c3b-6110-4f44-94e1-ca17dc4367d8.jpg

v. The DC supply of single phase bridge inverter is 350V. For quasi-square wave output voltage with a 70 percent ON time and frequency is 50HZ, the RMS value of output voltage is: (a) 292.8V (b) 220.5V (c) 250.6V

v. The DC supply of single phase bridge inverter is 350V. For quasi-square wave output voltage with a 70 percent ON time and frequency is 50HZ, the RMS value of output voltage is: (a) 292.8V (b) 220.5V (c) 250.6V

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Q2 (a) Figure Q2(a) shows a single-phase full-bridge square-wave voltage source inverter has resistor (R) and inductor (L) load of 10 Q and 5 mH respectively connected in series. The inverter output frequency is 50 Hz. The transistor switching scheme is complementary bipolar. (i) Draw the output voltage and current waveforms. (ii) Obtain an expression of the rms output voltage at the fundamental frequency. (iii) If the fundamental AC output voltage is 220 V, find the required DC input voltage for the inverter. (iv) Find the instantaneos load current by considering until the 9th harmonics number. (v) Calculate the total harmonics distortion (THD) of the load current. Use only the first three odd harmonics. (vi) Sketch the harmonics spectrum for output current. (vii) Show the displacement angle a, if 5th harmonic is to be eliminated.
d.c. load line. It is the line on the output characteristics of a transistor circuit which gives the values of IC and VCE when signal is applied when no signal is applied O corresponding to a.c. conditions. other A half wave rectifier is equivalent to a clamper circuit. a clipper circuit. a clamper circuit with positive bias a clamper circuit with negative biasd. O
8-The waveform of output voltage of half-controlled three phase bridge rectifier in each cycle contains: Two- pulse six- pulse three- pulse 9-The DC supply voltage of single phase bridge inverter is 300V. For quasi-square wave output voltage with a 60 percent ON time, the RMS value of output voltage is: 232.37V 220.5V 270.9V 10-For three phase bridge inverter with 120° conduction and resistive star-connected load, the waveforms of: (a) The load current and line voltage are quasi-square. (b) The load current is quasi-square and line voltage is a six- step. (c) The load current is six- step and line voltage is quasi-square. 9.
4) Consider a power supply consisting of a transformer, a half-wave, 1-diode rectifier, and an output filter capacitor. The rectifier diode is now replaced with a bridge (4-diode) rectifier. Neglecting the diodes’ turn-on voltages, What is the value of the ripple output voltage.
(i) With necessary sketch, write the load current flow path of a single phase semi converter during freewheeling period. Assume the load have resistance and high inductance value and the semi converter requires multiple gate pulse for triggering. (i) Draw the circuit diagram of the single phase half wave controlled rectifier (RL load) with center-tapped transformer and compare its performance with uncontrolled rectifier operation.
1.. . is a voltage controlled device. 2. The controlling parameter in MOSFET is . 3. A thyristor is a -layer semiconductor material device.
Calculate the VDC, IDC, VLPK, ILPK, VLRMS, ILRMS through the load connected to a half – wave rectifier using 2nd approximation in the figure shown.
1-Write the characteristics of NTC.? 2-Draw the Characteristic curve of PTC.?
I need a diagram of a circuit by the transform and rectification block, using the bridge rectifier circuit (KBJ1008). It can be a source of any value. You don't need to do any calculations, just a drawing of how this circuit will look, please.
An integrated circuit is ..A. A complicated circuitB. An integrating deviceC. Much costlier than a single chipD. Fabricated on a tiny silicon chip
Design rectifier circuits to provide an output of 100 Vpc using a.) HWR b.) Center-tapped FWR and c.) Bridge-Type FWR circuits. For each circuit, calculate the transformer peak voltage rating, the diode PIV ratings, and the transformer turns ratio, if power is taken from the 220V line ac supply.
I need a diagram of a circuit by the transform and rectification block, using the bridge rectifier circuit (4 diodes). It can be a source of any value. You don't need to do any calculations, just a drawing of how this circuit will look, please.