+ Usl W R₁ US2 + ww R₂ + US3 www R3 ww RA M 1) What circuit configuration is this? 2) Find to in the given circuit if the op amp is ideal. Show all your work, do not skip steps. 1 R5 Vs1 = 4.0 V; Vs2 = 1.0 V; Vs3 = -2.0 V; - R1 = 44.0 kΩ ; R2 = 27.5 kΩ ; R3 = 80.0 ΚΩ ; R4 = 220.0 kΩ ; Rs = 3.0 ΚΩ

+ Usl W R₁ US2 + ww R₂ + US3 www R3 ww RA M 1) What circuit configuration is this? 2) Find to in the given circuit if the op amp is ideal. Show all your work, do not skip steps. 1 R5 Vs1 = 4.0 V; Vs2 = 1.0 V; Vs3 = -2.0 V; - R1 = 44.0 kΩ ; R2 = 27.5 kΩ ; R3 = 80.0 ΚΩ ; R4 = 220.0 kΩ ; Rs = 3.0 ΚΩ

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter18: Resistive-inductive Parallel Circuits

Section: Chapter Questions

Problem 13PP: In an R-L parallel circuit, IT=1.25 amps, R=1.2k, and XL=1k. Find IR

See similar textbooks

Similar questions

3. Design an op-amp circuit that can perform this operation: Vo = 2 -V1 + 2V2. %3D 1. Circuit Diagram 2. Calculation with Assumptions
Create Op-amp circuit... with:Vin= -1 Volt (DC) Vout = 14 Volt (DC) Only resistors with 1k, 3k, 5k, 7k and 11k ohms can be used while the circuit is being built. The V+ value of the LM741 IC to be used for op-amps will be 20 volts and the V- value will be -20 volts. You need to use at least one inverting amplifier and one non-inverting amplifier to build the circuit. Question: Write the gain formula of the circuit and calculate it, and write how we should find the Vout value..
For this op amp, an equation needs to be made for V0 = Va + Vb. I thought it was -4(Va) + 4(Vb) as the difference, but that doesn't seem to be correct. The voltage limits for the output voltage are -0.8 V less than or equal to Vo less than or equal to 3.2 V. Can you show how to set up the equation for V0?
(a) Design and implement the give expression from given de voltage Vdc-10v using op-amp.R2=100ohm and R1-120ohm (b) Find out the output voltage form the given expression? Vout = { [1+2*1*13.35*Vde+2.26*Vdc] } R1
As an Electronic Engineer in XYZ Analog IC Design Centre, you are required to design Operational Amplifiers (Op-Amp). Based on combination of ideal Op-Amp as illustrated in Figure Q3 (b), derive the output voltages Vo1, V02, V03, and V04. If V₁ = 4 V and V2 = 2 V, determine V04. R Vio-W V₂0- 2R ww R R R __ Voi R R 3R V03 Voz Figure Q3 (b) 2R ww 4R M 2R R V04
1. For the circuit below assume an ideal op amp. Find Vo/Vs. R1 =2kQ2, R2 =5k0, R3 =8k and R4 =20k02. VB R1 www R4 VO
The circuit below, you may note, does not match any of the common op-amp circuits. By performing circuit analysis, determine the voltage across the load resistor R5. You may assume that V1 = 3.6 V, V2 = 4.7 V, R1 = 37 kQ, R2 = 62 KQ, R3 = 77 kQ, R4 = 71 kQ, and R5 = 90 kQ. R1 ww V1 + R2 V2 R3 R4 R5 mm D
The circuit below, you may note, does not match any of the common op-amp circuits. By performing circuit analysis, determine the voltage across the load resistor R5. You may assume that V1 = 2.4 V, V2 = 5.3 V, R1 = 42 kQ, R2 = 58 KQ, R3 = 48 kQ, R4 = 55 kQ, and R5 = 12 kQ. R1 ww V1 R2 V2 R3 www R4 R5 -
The circuit below, you may note, does not match any of the common op-amp circuits. By performing circuit analysis, determine the voltage across the load resistor R5. You may assume that V1 = 5.1 V, V2 = 4.2 V, R1 = 95 kQ, R2 = 63 KQ, R3 = 40 kQ, R4 = 28 kQ, and R5 = 73 kQ. R1 V1 R2 V2 + + R3 R4 R5 mn m
(d) Sketch a buffer circuit using an op-amp and explain its purpose/operation. Using inverting summing amplifiers design a circuit to add four inputs, V1-V3 in the following combination giving Vout = 4V₁ + 10V2 - 2V3
(b) Draw an amplifier circuit using an ideal op-amp that computes the average of 3 input signals. State clearly the value of the resistances given that the inputs are Vi = 5 V, V2= 3 V and V3 = 1 V and the output is Vout = -3 V.
Here is a single op-amp, shown under two different conditions (different input voltages). Determine the voltage gain of this op-amp, given the conditions shown. Also, write a mathematical formula solving for differential voltage gain (AV) in terms of an op-amp's input and output voltages. +12 V +12 V Va=1.00 V %3D Vout = 1.5 V +12 V V=1.00003 V %3D -12 V +12 V +12 V Va =1.00 V %3D Vet = 6.8 V +12 V V 1.00004 V -12 V