Consider the following instruction breakdown that decomposes an instruction into 4 parts: OPCODE DST SRC IMM OPCODE specifies the OPeration's CODE. DST specifies a DeSTination register. SRC specifies a SouRCe register. IMM specifies a 2's complement value (that's IMMediately available as part of the instruction). Assume the architecture has 32-bit instructions, 231 opcodes, and 32 registers. A.) What is the minimum number of bits required to represent an OPCODE? 8 B.) What is the minimum number of bits required to represent a register? 3 C.) What is the maximum number of bits that can be used to represent the IMM value? D.) What is the largest positive value in base 10 that can represented by the IMM value?

Consider the following instruction breakdown that decomposes an instruction into 4 parts: OPCODE DST SRC IMM OPCODE specifies the OPeration's CODE. DST specifies a DeSTination register. SRC specifies a SouRCe register. IMM specifies a 2's complement value (that's IMMediately available as part of the instruction). Assume the architecture has 32-bit instructions, 231 opcodes, and 32 registers. A.) What is the minimum number of bits required to represent an OPCODE? 8 B.) What is the minimum number of bits required to represent a register? 3 C.) What is the maximum number of bits that can be used to represent the IMM value? D.) What is the largest positive value in base 10 that can represented by the IMM value?

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter22: Sequence Control

Section: Chapter Questions

Problem 6SQ: Draw a symbol for a solid-state logic element AND.

See similar textbooks

Similar questions

Explain the SUB instruction of 8086. Compare it with SBB instruction. Write a Assembly language program for 8086 to find the square root of a number using SUB instruction. (Note : Solve the question in paper, scan and upload along with the other Part B and C answers) A BIE
- The stack memory is addressed by a combination of the plus offset. The PUSH and POP instructions always transfer between segment -bit number the stack and a register or memory location in the 8086 microprocessors. For string instructions, DI always addresses data in the segment. The 8086 LOOP instruction decrements register for a 0 to decide if a jump occurs and tests it
Subject name Digital logic design
8085 microprocessor went through its manipulation operation in the ALU, the results was transferred on the data bus and status of the results was stored in the flag register for indications . With your knowledge and understanding illustrate a complete bit configuration of 8085 flag register and show the functions of the represented bits in the register.
By using the design procedure for digital computers, design the following:i. Encoderii. Decoderiii. 4-bit comparator
P Flag question Explain the MUL instruction of 8086. Compare it with IMUL instruction. (1 +1 Marks) Write a Assembly language program for 8086 to find the cube of a number using MUL instruction. (5 Marks) (Note : Solve the question in paper, scan and upload along with the other Part B and C answers) B I III
Design a 3-Bit (fixed reference) comparator for 100 reference values. b) Logic Gates c) PROM d) PAL
Q4(a) Adder is divided into three types which are half adder, full adder, and parallel adder. Illustrate the implementation of full adder using half adder with necessary logic gates. (i) (ii) Figure Q4(a)(ii) shows the input timing diagram for a full adder. Illustrate the timing diagrams for output S and Cout- B Cin Cout Figure Q4(a)(ii) (iii) Given A = 111001 and B = 100010. Construct a 6-bit parallel adder to solve for A + B.
The upper 16 -bit binary count value are displayed on the four seven -segemnt displays as four hexadecimal digits. Hexadecimal values aren't good for human perception. How would you suggest the counter design be modified so that only decimal count values are displayed.
1. Write the contents of all registers and the conditions codes registers after each execution instructions in Table Q1(a). Instructions SUBS r0, rl, 12 MOV 12,13, ASR #3 ro 11223344 Table Q1 (a) rl F7770025 12 r3 CF119856 CF119856 NZ V C 010 1
A) List and describe 10 features of the Atmel ATmega 2560 AVR microcontroller (use the ATmega 2560 complete reference manual for help). B) List and describe two AVR instructions. As part of your description make sure that you list the operation for each instruction that is provided in the instruction set summary.
Draw the figure for memory segments with 8086 microprocessor software model. Explain the logical address structure used for each segment (Explain which registers are used in logical address presentation of each segment; segment address : offset address). Give an example solution to find the physical address in a segment from the logical address for 8086 microprocessor.