Using the open-loop transfer function the system below, where G= 144 s²+7.2s R(S) + Σ G(s) Y(s) What is the maximum magnitude of the frequency response in absolute value, Mpw, and the estimated settling time, T., of the closed-loop system? Choose the closest value. OM 1.04; T, = 0.5 seconds. OM 1.36; T, = 0.1 seconds. Mpw=2.07; T, = 2 seconds. OM = 1.16; T = 0.44 seconds.

Using the open-loop transfer function the system below, where G= 144 s²+7.2s R(S) + Σ G(s) Y(s) What is the maximum magnitude of the frequency response in absolute value, Mpw, and the estimated settling time, T., of the closed-loop system? Choose the closest value. OM 1.04; T, = 0.5 seconds. OM 1.36; T, = 0.1 seconds. Mpw=2.07; T, = 2 seconds. OM = 1.16; T = 0.44 seconds.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Find the transfer function for the circuit shown in the figure. Plot the amplitude graph of 2log10[H(jw)] and the phase angle graph of H(jw) Calculate the actual cutoff frequency? Calculate the true phase angle at the cutoff frequency?
50. A signal x(t) = = sinc (150nt) is sampled at a rate of a) 100 Hz, b) 200 Hz, and c) 300Hz. For each of these cases, explain if you can recover the signal x(t) from the sampled signal.
I really need help with this question. Please explain this and give me a clear solution. Thanks in advance. In the block diagram below, it depticts a simple phase-shift single-sideband mod-ulator.
Given the discrete time signal x[n] = cos((πn)/3) what are two different contiuous time signals that would produce the sequence when the sample frequency is 120Hz.
3. a) b) Write a short note on Nyquist Rate. Calculate the Nyquist rate in rad/sec and in Hz for, m(t) = 2 sinАnt · cosВnt
1. Suppose you have multiple sinusoidal signal sources with four different frequencies where fj-4, f;=3, fz=2, f4=1 and their amplitudes Aj=A2=A3=A4=1. Together these signals form the message (modulating) signal (as shown in the figure below). Now, create a MATLAB program using built-in functions to generate the DSB Amplitude Modulated signal, and then recover the original signal (generate the Demodulated signal) from the modulated signals for time 0
Electronic Since k = 0.35x10^3, VGSQ = 6.2 V, VGS(Th) = 2.4 V, RF = 100 MΩ, RG = 10 MΩ, RD = 7.6 kΩ, RS = 2.2 kΩ and RL = 21 kΩ in the circuit in the figure, the output voltage In which option is the amplitude value (Vout) given correctly? NOTE-1: E-MOSFET output impedance is rd = 70 kΩ and should be taken into account in calculations. NOTE-2: Capacitors are of negligible size at mid-band frequency. NOTE-3: It is within the 5 kHz mid-band frequency.
What is the average power dissipation in an RLC series circuit in which R = 100 Ω, L = 0.1 H, and C = 10 µF driven at resonance by a 100-V (rms) source? What do I need to know? 1) The problem's main concept. 2) A breakdown of the problems given information. 3)What formula(s) should be used for this problem? 4) A detailed set of steps leading to the solution(must include units for all steps) with a diagram if possible? Thank you!
Consider a circuit described by a frequency response represented by the red dotted line in the figure shown. If the input is vin (t) = 5 cos(2T * 50t) V, what is amplitude of vout (t)? 8. 4 -2 -4 -6 .... 30 50 100 200 300 500 1000 Frequency (Hz) O 9.98 V O 5.0 V O 3.97 V O 7.92 V 20 2. 10 Gain (dB)
Q1 A standard second order system has wn = 8.8 and = 0.29 Determine the frequency response %3D specifications wr and Mr and bandwidth. Also find number of oscillations before setting, in the step response.
For this problem, let x(t)= tri(t/T), where T-1msec. . Find the energy in xt), (t). J-00" b. Find the spectrum, X(f) = F(x(t)}. c. Find the absolute bandwidth in Hz. d. Find the null bandwidth in Hz. e. Find the equivalent bandwidth in Hz. f. Find the 98% energy bandwidth in Hz. Find the -20dB level bandwidth in Hz.
For a series RLC circuit with a sinusoidal input voltage, the amplitude of the current passing through the circuit (lo in mA) is plotted as a function of frequency for two cases: Curve 1 with R1, L1, and Curve 2 with R2. L2 as shown in the next figure. The value of the capacitor used in the circuits is C=0.01 micro Farads. The quality factor (Q1) for curve 1 is about: 7.5 5- 2.5 1-10 1-10 1-10 1-10 Frequency (f), Hz O a. 20000 Hz O b. 0.5 O c. 0.23 O d. 2 O e. 1.5