(7.15* Microwaves of frequency 3 x 10¹0 Hz are beamed directly at ametal reflector. Neglecting the refractive index of air, determine the spac-ing between successive nodes in the resulting standing-wave pattern.odsalsups qolavas ssrli yo7.16* A standing wave is given byyo babivib sqolevisabutilqms gaisdE = 200 sin7x cos 3ntDetermine two waves that can be superimposed toC.E.A sugh Is Mgenerate it.ubor

When microwaves are beamed directly at a metal reflector, the incoming (or incident) waves and the…

7.15* Microwaves of frequency 3 X 1010 Hz are beamed directly at a metal reflector. Neglecting the refractive index of air, determine the spac- ing between successive nodes in the resulting standing-wave pattern. Bing om alsups qolavns srl to bo noq sili ya babivib qolavas 7.16* A standing wave is given by E = 200 sin 7x cos 3πt abutilqms gaisd de 15.9 sught IST Determine two waves that can be superimposed to generate it.

7.15* Microwaves of frequency 3 X 1010 Hz are beamed directly at a metal reflector. Neglecting the refractive index of air, determine the spac- ing between successive nodes in the resulting standing-wave pattern. Bing om alsups qolavns srl to bo noq sili ya babivib qolavas 7.16* A standing wave is given by E = 200 sin 7x cos 3πt abutilqms gaisd de 15.9 sught IST Determine two waves that can be superimposed to generate it.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

3) Solve the cutoff frequency for the first mode and second mode of WR975 Wave guide TABLE 7.1 Some Standard Rectangular Waveguides Waveguide de signation a (in) b (in) t (in) fe, (GHz) Frequency range (GHz) WR975 9.750 4.875 0.125 0.605 0.75-1.12 WR650 6.500 3.250 0.080 0.908 1.12–1.70 WR430 4.300 2.150 0.080 1.375 1.70-2.60 WR284 2.840 1.340 0.080 2.08 2.60-3.95 WR187 1.872 0.872 0.064 3.16 3.95-5.85 WR137 1.372 0.622 0.064 4.29 5.85-8.20 WR90 0.900 0.450 0.050 6.56 8.2–12.4 WR62 0.622 0.311 0.040 9.49 12.4–18
If a wave guide has he inner and outer conductor diameters of 0.0645 and 0.0215 inches respectively for a co axial lines then the cut off wave number is: a) 298 b) 300 c) 285 d) 123
Problem: Caleulate Average value, Rins value and Form faetor of the sawtooth wave show in the figure. WA
Imagine a two-dimensional system in which a sinusoidal waveform is excited at the exact center of a circular plate. The standing wave pattern is established when the excited wave two-dimensionalwaveforms for a stable equilibrium pattern of constructive and destructive interference with the reflected waves from the edge of the circular plate. Draw what you expect the standing wave patterns to look like in this two-dimensional system for increasing resonant harmonics, n. Explain what characteristics of the oscillating plate affect the value of those resonancefrequencies, and what geometric properties of the plate affect the patterns.
This is in radio wave propagation in Electronic Communication System the critical frequency at a particular time is 11.6MHZ. What is the MUF for trasmitting station if the required angle of incidence for propagation to a destination is 70 degrees. Show solutions
3. Generate a square wave of 0.5Hz with a duty of 50% on pin P1.0 as XTAL = 12 MHz. U1 12DXINT PODADO P0.1/AD1 PO 2/AD2 18 XTAL2 PO.3/AD3 P0.4/AD4 34 PO.S/ADS PO.6/AD6 9 32 RST PO.7/AD7 P2.0IAS 21 P2.1/49 P22/A10 PSEN ALE P2 3/A11 P2.4/A12 P2.5/A13 P2.6/A14 25 26 EA 20 P2.7/A15 10 P1.0 2 P1.1 P12 P1.3 P3.ORXD P3 1/TXD11 P32TS 12 P3.3ANT113 P1.4 P1.5 P34/7014 P15/T1 P3.6WR 15 16 17 P1.6 P1.7 P3.7/RD 50651 4 4 I R1 0.01 R2 0.01k D2 LED-BIBY D1 ■ LED-BIBY 30 31 -2.1
this is not sinusoidal wave use general formula D=25 A message Signal is given by m(t]> cos(10OTTt) t Dos (asot). The message is to be transmitted AM-LC with modu laLion index o.6. using (2 Eind amplitudde and pouer of carner Find par effiaeny ok AM-Lc ystem.
An EM wave comes from air to a surface with a relative dielectric value of 90. What is the angle of transmission when no reflection occurs? 7.56° 6.01° 63.8° 6.38°
Q. (a)Two nicols are first crossed and then one of them is rotated through 600. Calculate the percentage of incident light transmitted. Q. (b)Two nicols are oriented with their principal plane making an angle of 600.What percentage of incident unpolarized light will pass through the system? Q.The signal retrieved in an optical fiber reduces at its output to one-tenth of its input power. What is the overall attenuation? What shall be the power at output in a fiber having loss3 db/km?
For the trapezoidal current wave-form, determine the effective value. I (A) 1.22^2* peak current I B 1.67^2 * peak current Im 0.6^0.5 * peak current D) 0.775^0.5* peak current ji B t 3T 20 T/5 -1/₂ C 7T 20 E
A 2 V signal is incident to the interface from a 75 Ohm region propagating to a 50 Ohm impedance region. What is the reflection coefficient? What is value of the incident, reflected and transmitted wave? What voltage would you measure on either side of the interface right after the signal goes through the interface. For the interface, I'm a little confused. I used a voltage divider and got V_transmitted = 0.8 and V_incident = 1.2. But shouldn't they be the same?
What is a waveguide? What is a slab waveguide? What is a planar waveguide? What is thin slab?