Using the method of sections, DRAW THE SHEAR AND BENDING MOMENTS DIAGRAM The solution should include: -Reaction Supports -Shear Equations -Bending Moment Equations -Points of zero shear (if any) -Maximum Shear and Bending Moment 100 N 208 N/m 90 N.m 3 m B 30 N/m 3 m 1.5 m 85 N/m 2.5m D 215 N/

Using the method of sections, DRAW THE SHEAR AND BENDING MOMENTS DIAGRAM The solution should include: -Reaction Supports -Shear Equations -Bending Moment Equations -Points of zero shear (if any) -Maximum Shear and Bending Moment 100 N 208 N/m 90 N.m 3 m B 30 N/m 3 m 1.5 m 85 N/m 2.5m D 215 N/

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

es A 4-m cantilever beam is loaded as shown. The cross section is formed with two concentric circles of radii 45 mm and 35 mm. If the allowable stress is 150 MPa, F Ra 1 X Y 12 Determine the section modulus of the beam. Select the correct response: 72113.831 mm³ 87833.695 mm³ 57962.384 mm3 45378.561 mm³ Ri 12
The figure (all dimension are in mm) below shows an I-section of the beam. The shear stress at point P (very close to the bottom of the flange) is 12 MPa. The stress at point Q In the web (very close to the flange) is: N'-. 100- P Q 201 100- T 20 81484 80 20 40 --N (a) Indeterminable due to incomplete data (6) 60 MPa (c) 18 MPa (d) 12 MPa 068
Problem 4 The beam loaded as shown below, compute the bending stresses at every 1m from the fixed end support of the beam use Ina = 100x106 mm4 www 10 kN 4 kN/m bm 러 n.a. 130 mm 200mm
For the given W8x35 I-Beam and the loading condition shown in the image, determine the maximum shear stress and maximum bending stress. Report values to two decimal place accuracy. 6 kips T σ = -100 2 kips/ft Shape W8x35 6 ft 250 12.678 150 100 50 -50 12.575 -50 C 6 ft 50 ksi ksi Material Structural Steel D 2 ft 203.708 B 100 7.874 203.708 150 I W8x35 E (MPa) 200000 200 206.248 V 0.27 250 30 p (kg/m³) 7850 Geometric Properties A Cz Cy 1₂ ly rz Ty Az Ay J r 6645.148 101.854 103.124 Bending Properties 52861000 17731000 89.0998 51.6647 Shear Properties 4438.033 1506.905 Torsion Properties 320081.964 18.219 mm² mm mm mm4 mm4 mm mm mm² mm² mmª mm
A cantilever beam with a 'T' shaped cross-section is loaded with a distributed load as shown below. The intensity of the distributed load is 100N/mm. b = 6.25mm and c=6.25mm. A y Parameter L a d 0 L B 777 Description Beam length T Width of the flange Height of the web Yield stress |←0 →| Value 250 80 75 250 y Units mm mm mm MPa You are tasked with ensuring the beam can withstand the applied loading. To do this you must: a) Calculate the centroid for the given cross-section. Your value of y should be measured from the bottom of the section. Determine an expression for Q (statical moment of area) for the given shape. The expression(s) for Q should be in terms of the variable, y, measured from the bottom of the section.
A steel bar 20mm Dia. and 250 mm long is subjected to tensile load. Determine the length of the bar when the axial stress is 420 MPa given that the elastic modulus of the bar material is 200 GPa. Select one: O A. 255.0 mm O B. 249.575 mm O C. 250.525 mm O D. 252.125
Question 4 • h₁-100mm . • h=120mm • t-5mm • b-75mm Z O ko An I beam is subjected to an internal shear force, V, of 325kN. The dimensions for the I-beam are Answer h₁ h Determine the maximum transverse shear stress in the web. Enter your answer in MPa to one decimal place. Your Answer:
A horizontal 50 kN load is applied on a 610UB125 Beam as shown in Figure 4. Determine the stresses at four corners A, B, C and D. Also, determine the angle that the neutral axis forms with the horizontal plane. The sectional properties are given in Table 1. 50k! 306 50 KN Table 2. Figure 4 (unit in mm) 306 mm bf d Y, A tr tw Section mm² mm mm mm mm 610UB125 16000 229 612 19.6 11.9 Sx lyo Sy (x106 (x10³ (x106 (x10³ mm²) mm³) mm²) mm³) 986 3680 39.3 536
below, compute the magnitude of the force (F) required to break contact at point (c)? 3 m s = 10 mm K = 1800 N/m WWQ 3 m 4 m 4m In your hand F
OP N C What is the shear resistance of a universal beam (UB) with the following dimensions [EC3 Section 6.2 Resistance of cross sections]: Cross sectional area A = 105 cm² Height h = 584.6 mm Flange thickness t = 11.4 mm Flange width b = 213.2 mm y-y Web thickness tw = 7.8 mm Root radius r = 12.7 mm Yield strength fy = 355 N/mm² Calculate the shear resistance and give your answer to the nearest whole kN. Do not include units in your answer.
L For the beam shown above with length L = 7 m with the applied uniformly distributed load of w = 17 kN/m, what is the maximum bending stress if the beam has a cross section with the following dimensions: b = 100 mm d = 250 mm tf = 20 mm tw = 15 mm %3D b tw O bending MPa Round to one decimal place
Problem 13 A flanged bolt coupling consists of seven steel 20mmp bolts spaced evenly around a bolt circle 300mm in diameter. Determine the torque capacity of the coupling if the allowable shearing stress is 40MPA. R