use the constant voltage drop model in analyzing the diode circuit below 10 Ω M V₁ (+ D₁ If V₁ is -3 V, what would be the state of the diodes? A. D₁ and D₂ are both OFF B. D₁ is OFF and D₂ is ON D₂ C. D₁ is ON and D₂ is OFF D. D₁ and D₂ are both ON If V₁ is 2 V, D₁ is OFF and D₂ is ON. What is Vo? A. 0.3 V B. 0.7 V C. 1 V + 1092 Vo D. 1.7 V

use the constant voltage drop model in analyzing the diode circuit below 10 Ω M V₁ (+ D₁ If V₁ is -3 V, what would be the state of the diodes? A. D₁ and D₂ are both OFF B. D₁ is OFF and D₂ is ON D₂ C. D₁ is ON and D₂ is OFF D. D₁ and D₂ are both ON If V₁ is 2 V, D₁ is OFF and D₂ is ON. What is Vo? A. 0.3 V B. 0.7 V C. 1 V + 1092 Vo D. 1.7 V

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter59: Motor Startup And Troubleshooting Basics

Section: Chapter Questions

Problem 12SQ: How is a solid-state diode tested? Explain.

See similar textbooks

Similar questions

How is a solid-state diode tested? Explain.
What is CEMF?
What is the difference between a diode and rectifier?
Given the following circuit with VDD= 9.2 V, R=2.3 k2, then the current Iis: Use the CVD model for the diode, with VD = 0.65 V. I VDD a. 0.004000 A O b. 3.717391 A OC. 0 A d. 4.000000 A e. 0.003717 A R + VD -
A- If V, is a sinusoidal voltage with Vm = 40 V, and V= 15 V. Plot the waveform of the output voltage in each of the following clippers circuits assuming ideal diodes. B- Repeat part (A) if the diodes are silicon diodes. R R R (a) (b) (c) (d)
uO 9:.0 A docs.google.com * ZAIN IQ l. Q3/B: Assume an ideal diode model for all the diodes in the circuit below. calculate voltages and currents through D1 and D2 9kQ 1N1199C R2 D1 18KQ 1N1199C D3 1N1199C V2 =12 V R3 1kQ R4 5kQ 1.22 V 11 mA 0.5 A O VD1 ID1 VD2 ID2 صفحة 4 من 6
For the circuit shown in the Figure, if the diodes are silicon diodes with Vp(on)=0.7 V, and VIN=50 sin wt V, V1 =6 V and V2 = 16 V, then the value of VouTP-p) is: R, D VaN Vout v1事 2章 Oa. 25.4 V Ob. 27.4 V Oc. 29.4 V Od. 23.4 V
All pn diodes shown below have a voltage drop of 0.3 V when they are "ON". +4V DIA 5k2 D2 VOUT VA 5k2 V8 D1B -2V Indicate in the table whether the diodes D1A, D1B and D2 are ON/OFF with the given VA and VB values. Also give the corresponding VOUT numerical values. DIA (ON/OFF) DiB(ON/OFF) Dz(ON/OFF) VoUT (sign and numerical value) VA |V8 OV +4V OV +3V ov +4V
2. Figure A.1 shows I-V characteristics of two diodes, namely A and B. Diode A has higher dynamic resistance than diode B. UTM &UT ID 4 5UTM 3TM UTM UTM &UTM 5 UTM & UTM UTM 3 UTM 03 TM 6 UT 0.68 (a) UTM VD Figure A.1 State one possible reason why the diodes have different knee voltage values. UTM OM & UTM 3 UTM & TM (b) Based on Figure A.1, identify the knee voltage of UTM" TM 5 UTde BE UTM
Question 1: In the circuit shown below, the output (Vo = 10V Max.) Unipolar. The frequency of Primary is 60 Hz. The diodes are Silicon with VD = 0.7V. a. Sketch the output without a Capacitor. b. Determine Voc without a Capacitor. c. Sketch Vs (at the Secondary). d. Determine Voc with a Capacitor of 10 uF across RL. e. Determine the RMS Value of Vp (at the Primary). f. PIV (Peak Inverse Voltage). 10:1 Output C. 22 k1 All diodes are IN4001. | 00000
Power supply circuit is delivering 0.5 A and an average voltage 20 V to the load as shown in the circuit below. The ripple voltage of the half wave rectifier is 0.5 V and the diode is represented using constant voltage model. The smoothing capacitor value is equal to 220V omsh RL VI-DC20V 0.01 F 0.02 F 0.0167 F None of the above
Consider the circuit shown below. The reverse saturation current is 1x10-¹6A and R₁=3kQ2. Vin 5V. D₁-D4 are the same. Vin P₁ # Ri M P₂ D3 Dy + Vout (a) What should be the current flow through the diodes? Use the full exponential model to analyze this. (b) What is Vout? Use the full exponential model to analyze this. (c) Suppose, Vin is increased by 0.1V. What will be the increase of Vout? Use the full exponential model to analyze this.