/ Use counter 1 of 82C54 interval timer in order to generate a contimmous series HIGH time of 49usec and LOW time of lusec. If CLK 1 of counter I is IMHZ, write an 8086 program to generate the required signal. Note: counterl addres register address of 8254 is C6H.

Q: If MN/(MX)' signal is high, 8086 processor works in mode.

A: 1) 8086 Processor supports below modes.  In minimum mode there can be only one processor i.e. 8086.…

Q: 3) Write a Verilog code for a 5-bit up/down counter. The counter has reset and enable control…

A: Up Down counter is the combination of both the counters in which we can perform up or down counting…

Q: 10. Write an ALP to rotate right the contents of AL register 4 times including carry and save the…

A: Program Approach : Moving the contents of variable into accumulator . Store the value 4 in register…

Q: rollback up/down counter. Make sure to include a control signal called “count-direction” in your…

A: 3-bit rollback up/down counter. Make sure to include a control signal called “count-direction” in…

Q: Write an ALP to copy 48h into AL using immediate addressing mode, 5876h into [2500h] using based…

A: Actually, Addressing mode refers to the way in which the operand of an instruction is specified.

Q: 1. Design a 32-bit counter that will either increment by 4 or load a new 32-bit value, D, on each…

A: GIVEN:

Q: Use counter 1 of 82C54 interval timer in order to generate a continous series of pulses which have…

A: 8254 programmable interval timer: 8254 is a designed solve the timing control problems in…

Q: A switch-tail ring counter (Johnson counter) uses the complement of the serial output of a right…

A: Johnson Counter: The 4-bit Johnson counter or the modified ring counter consists of four 'D'…

Q: Write an alp to copy 4548 into AX using immediate addressing mode, 76h into [2500] using indexed…

A: The given information is writing an ALP to copy 4548 into AX using immediate addressing mode and 76h…

Q: i- Describe an assembly program for PIIC18 to toggle all bits of PORTB, PORTC and PORTD every ½ of a…

A: 3) Assembly program is given below to create a square wave of 75% duty cycle on bit 0 of PORT C

Q: Write a procedure named CountBits that counts the nuber of 1 bits in the contents of the EBX…

A: Below we write a simple assembly code for number of one's:…

Q: how to solve please show working

A:

Q: Counter implementation using timer 1 module in timer mode.Each incremental value will have delay of…

A: #include <stdio.h>#include <stdlib.h>#include<pic16F877A>void Timer0Delay(void);…

Q: Write an AVR assembly program for the ATMega32 to generate a time delay of 20 us using Timer 0 with…

A: We need to write an AVR assembly program for the ATMega32 to generate a time delay of 20 us using…

Q: The Adder/Subtractor includes a “switch" which is a set of multiplexors. Assume registers A and B…

A: adder/subtractor:It is capable of adding and subtracting in same circuit.

Q: Subject-Microprocessor Write an ALP in 8085 to convert two digit BCD number into Excess-3 code. (BCD…

A: Below is an example of an 8085 assembly language program to convert a two-digit BCD number stored in…

Q: 1. Test the circuit above (use your own input values) and note down the sequence of outputs in Table…

A:

Q: Implement the following RTL code using n-bit parallel adder and registers a: X+X+Y a': X+X+Y' +1

A: Step 1 The answer is given in the below step

Q: 1.Draw the diagram of a 5-bit "Do Nothing "register using D flip-flop. 2. Given an initial value of…

A:

Q: Using the SR latch and its truth table complete the timing diagram for the outputs, Q, and Q. R S Q…

A: S-R Latch are the simplest form of latch are implemented using two input S for set and R for Reset…

Q: Write an assembly line to initialize register ebx to hexadecimal value 2AEF, using the long option…

A: To initialize the register EBX to the hexadecimal value 2AEF using the long option (32-bit), the…

Q: analog value that is connected with IN+ pin of ADC080

A: Q. Write an assembly language program to read the analog value that is connected with IN+ pin of…

Q: B) Wha

A: Below I have provided the handwritten soluction to the given question

Q: create a switch level implementation using NFETS and PFETS. Here you can assume you have the…

A: D is correct

Q: By using metode masking and Bit Test instructions, perform sequentially for the E87AH number (write…

A: We need to perform the mentioned operations on given data bits.

Q: 4. Write the equation between the time delay generated by the 8051’s Timer in mode 1 and the initial…

A:

Q: Please answer the following question using only one 3-bit binary counter with clear input and the…

A: To generate a specific sequence of numbers using a 3-bit binary counter with clear input, a…

Q: Referring to the register transfer system below, determine the transfer operation, which will happen…

A: Answer

Q: Suppose that the EAX register contains FFFFFFC8 and the instrucution add eax, 211 is executed. What…

A: We have given a register EAX. We have to perform the addition of a value with the value stored in…

Q: Write an APL to perform the shift logical right operation of 8086

A: Shift instructions of the 8086 can perform two basic types of shift operations The logical shift and…

Q: Design a synchronous 2 Bit uP Counter using SR

A: Synchronous CounterSynchronous Counters square measure therefore known as as a result of the clock…

Q: Q2. Using 74LS163 4-bit binary counter and any nessary gates, design a counter that produces the…

A: Using 74LS163 4-bit binary counter and any necessary gates solution : 4 bit binary counter (…

Q: Figure 1.5(a) shows the Verilog implementation of a module digital_block with a clock input cik, a…

A: Sequential Logic Circuits use flip-flops as memory elements and in which their output is dependent…

Q: It is desired to configure a PWM Output Pin on an Almega328P. Write the A that will set up an output…

A: the solution is an given below :

Q: PICmicro A/D converter has been configure and the following register values are provided: ADCONO =…

A: The value in decimal read on ADRESH register is

Q: ck cycle. When E = 0, it stops counting and output stays unchanged. clr is clear input. When clr =…

A: SummaryTo generate a specific sequence of numbers using a 3-bit binary counter with clear input, a…

Q: Q2. Write a routine for 8051 to create a rectangular wave (on port 2, bit 1) of 66% duty cycle using…

A: According to the information given:- We have to write assembly code in 8051 to create rectangle wave…

Q: Using Logism Softwarel The most important and possible most difficult component to implement is the…

A: To design the 8-bit arithmetic logic unit (ALU) using Logisim software, you'll need to break down…