UPVOTE WILL BE GIVEN. ANSWERS ARE GIVEN ALREADY. PLEASE WRITE THE COMPLETE SOLUTIONS. A room contains moist air with a dry bulb temperature of 25°C and a wet bulb temperature of 21°C. Find a) Specific Humidity (Ans. W = 0.0139) b) Relative Humidity (Ans. RH = 69%) c) Specific Volume (Ans. V = 0.863 m³/kg) d) DPT (Ans. DPT = 19.1°C) e) Specific Enthalpy (Ans. h = 60.5kJ/kg)

Q: COMPLETELY WITH A DIAGRAM. THE ANSWERS ARE ALREADY GIVEN. DO THIS TYPEWRITTEN FOR UPVOTE

A: Given-Information:- AB = 150 mmBC = 300 mmCD = 225 mmCE = 500 mmNAB = 240 rpm To-Determine:- 1.…

Q: A wheel is mounted on a shaft (G= 80x10^9 N/m^2) of length 3 m and radius 1 cm. The wheel is rotated…

A:

Q: If the two 304-stainless-steel carriage bolts of the clamp each have a diameter of 10 mm, and they…

A:

Q: Given the cable tension T = 80 lb, determine a) the moment about point A due to T, and b) the…

A: Given   Tension, T = 80 lb Distance, AB = 32 in Find   Moment, A   Shortest distance x

Q: There is a position tolerance applied to a four hole pattern and another position tolerance to a…

A: Introduction Tolerances in mechanical engineering describe the allowable deviation from stated…

Q: Can the system in given figure be in static equilibrium in the position shown? The uniform bar AB…

A: Given Bar AB = 500 lb Block C = 300 lb Coefficient of friction = 0.4 To find Verify the system…

Q: At room temperature (20°C), a 0.5-mm gap exists between the ends of the rods shown. The temperature…

A:

Q: 1. A system is needed to be designed as damped spring mass system. Calculate the amplitude of…

A:

Q: It is observed that the skier leaves the ramp A at an angle A = 22° with the horizontal. (Figure 1)…

A: Given Data The angle at A is: θA=22° The distance of B is: B=100 m The height of A is: A=4 m The…

Q: The catapult is used to launch a ball such that it strikes the wall of the building at the maximum…

A:

Q: A perfect gas undergoes isothermal expansion, which increases its volume by 2 dm3. The final…

A:

Q: Draw a schematic diagramof each problem with labels of states of a substance; For uniformity…

A:

Q: A circular cylindrical specimen 20 mm in diameter has been subjected to a uniaxial load in tension…

A:

Q: A piston-cylinder assembly contains 0.4 lb of air initially at a pressure of 30 lb/in² and a…

A: Given that: m = mass of air inside the cylinder = 0.4 lb P1 = 30 lbf/in2 T1 = 200 oF k = specific…

Q: Swinging caliper disc brakes have the following advantages when compared to internal shoe drum…

A: Break: It is a mechanical device that absorb the kinetic energy of the vehicle and convert it into…

Q: article moving in the x-y plane has a position vector given by r = 0.55ti + 1. radius of curvature p…

A: The object's velocity function's first-order derivative, acceleration. Two aspects of an object's…

Q: Problem#1: The coefficient of friction between the inner pulley and the belt is 1/π. Find the…

A:

Q: 4- A helical compression spring is made with oil-tempered wire with wire diameter of 0.2 in, ean…

A: Dear student, in this solution, I have taken some standard values for oil tempered wire from…

Q: If the base of the triangles is 1m below the surface of 20 degrees Celsius of water, determine the…

A: Givenx=1mb=4mh=3m

Q: Q4: Assuming f-0.020, determine the discharge in the pipes. Neglect minor losses. Pipe Diameter AB…

A:

Q: 2. Determine the forces in member BC, BE and EF of the truss shown in the figure by Method of…

A: Dear student, as per the given diagram the data given is wrong. As per my knowledge, I have…

Q: Given: Water (p = 1000 kg/m³) flows past a half body as shown in the figure. Pressure is measured at…

A: Given data: PA=160 kPaPB=90 kPa To find: Velocity of uniform stream, U

Q: A 5m³ tank contains saturated air at 25°C (Psat = 3.169 kPa) and 97 kPa. Determine the following:…

A:

Q: Counterflow heat exchanger is designed to heat fuel oil from 30-90degC while the heating fluid…

A: Givencounter flow heat exchangerTc1=30oCTc2=90oCTh1=140oCTh2=150oC

Q: B. Given the barometric pressure of 14.696 psia (29.92 in. Hg as. ), Make these conversion: a. 96…

A:

Q: Shifting from second to third gear in a car is an example of which type of motor skill?   Question 4…

A: Explanation: Open Motor skill: it involves the motion of supporting surfaces, objects, or people in…

Q: Consider two degree of freedom of coupled pendulum with horizontal rod vibration system are shown in…

A: Given: To find: Equation of motion State space model

Q: A compressor is to be used to draw air from the outdoors where the conditions are 26.5 C and 100.04…

A: The given information in the problem is listed in the following attached image:

Q: ads are applied to the compound rod that is composed of an aluminum segment rigidly connected…

A: Given:P=10 kNArea of bronze, Ab=400 mm2Area of aluminium, Aa=600 mm2Area of steel, As=300 mm2

Q: Fatigue accounts for ~90% of mechanical engineering fai es that may be taken to increase the…

A: Introduction: If a load is continually withdrawn and restored after being of insufficient size to…

Q: A cold-drawn steel rod of circular cross-section is subjected to an axial load varying from 5000 lb…

A: Given data:- The cold drawn steel rod of circular cross-section is subjected to an axial varying…

Q: Five lbs of propane is contained in a closed, rigid tank initially at 80 lbf/in.², 150°F. Heat…

A:

Q: A simple ideal Rankine cycle with water as the working fluid operates between the pressure li the…

A: GivenP1=10MPaP2=10kPaT1=500oCm=165 kg/s

Q: Determine the volume, in ft3, of 2 lb of a two-phase liquid-vapor mixture of Refrigerant 134A at…

A:

Q: ii. III. iv. For uniformity purposes, assign STATE 1 at the inlet of a high-pressure turbine. The…

A:

Q: A canal of trapezoidal section has bed width of 8 m and bed slope of 1 in 4000. If the depth of flow…

A:

Q: 8. Water at a pressure of 1600 kPa has a quality of 30%. a). Find the phase. b). Determine the…

A:

Q: Determine the volume change, in ft3, when 1 lb of water, initially saturated liquid, is heated to…

A:

Q: A ball is thrown so that the motion is defined by the equations x = 4+ and y = 4+5+-4.82+² where x…

A:

Q: Two a right circular cylinder made of aluminum and another cylinder made of steel as shown in figure…

A: Given:Force applied, F=500 kNFor steel:Es=200 GPads=30 mmLs=1.2 mFor Aluminium:Ea=70 GPada=20…

Q: Steam, initially at 700 lbf/in.2, 550°F undergoes a polytropic process in a piston-cylinder assembly…

A: P1 = 700 lbf/in2 T1 = 550 oF P2 = 2900 lbf/in2 Kinetic and potential energies are neglected.…

Q: The fireman wishes to direct the flow of water from his hose to the fire at B.(Figure 1) Figure VA…

A:

Q: The figure above shows a schematic of a gas turbine engine. Engines such as these provide thrust to…

A: Given questions are related to machine design, material science  and manufacturing engineering.

Q: Water at 150°F flows in a straight 0.863-in-diameter iron pipe (e -0.00015ft) between points A and B…

A: Given   Diameter, d = 0.863 in      Length, L = 350 ft Pressure, P1 = 8.35 psi                P2 =…

Q: Assuming f-0.020, determine the discharge in the pipes. Neglect minor losses. Pipe Diameter AB BC BD…

A: f = friction factor = 0.020 LAB = 1200 m, dAB = 250 mm LBC = 600 m, dBC = 200 mm LBD = 800 m, dBD =…

Q: A block of wood is tested in direct shear using the loading frame and test specimen shown in the…

A: Given: Load→P=16 KN Height of the plane AB: →h=50 mm And width perpendicular to the plane: →w=100 mm…

Q: ho Axis of rotation Free surface Zs he r R Q10) Consider a vertical cylindrical container partially…

A:

Q: What is the mass in grams and weight in dynes and in gram-force of 12 oz. of salt? Local g is 9.55…

A:

Q: A room being air conditioned is held at 25°C db & 50% RH. A flow rate of 5m³/s of supply air at 15°C…

A: Given data P=100 kPaV1=5 m3/sT1=15°C Here, P is the pressure and V1 is the volume of the air flow.…

Q: What is the equivalent mass flow rate ( kg/hr ) of water delivered at 250 gpm. Water is delivered at…

A: GivenPart 1Q˙=250 gpm   m˙= ?  kg/hr