Complete all parts to the problem, thanks!! All different parts are for the one problem On a trip ofd miles to another city, a truck driver's average speed was x miles per hour. On the return trip, the average speed was y miles per hour. The average speed for the round trip was 40 miles per hour.20x(a) Verify that y =x - 20Total distanceAverage speed =Total time40 =(d/x) + (d/y)40 =y + x40y + 40x =40x =40y40x =(x- 20)What is the domain? (Enter your answer using interval notation.) (b) Complete the table. (Round your answers to three decimal places.)25354555(c) Find the limit of y as x approaches 20 from the right. (If an answer does not exist, enter DNE.)Interpret its meaning.As x gets close tomi/h, y becomes larger and larger

(a) Distance between the cities = d miles, Average speed while going = x miles per hour, Time…

Un a trip ofd miles to another city, a truck driver's average speed was x miles per hour. On the return trip, the average speed was y miles per hour. The average speed for the round trip was 40 miles per hour. 20x (a) Verify that y =

Un a trip ofd miles to another city, a truck driver's average speed was x miles per hour. On the return trip, the average speed was y miles per hour. The average speed for the round trip was 40 miles per hour. 20x (a) Verify that y =

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q 1: Why strength of materials and testing are important.
i need the answer quickly
Need 5 points shear stress material material resistance
Find force applied Work done=101.232 J Dispalcement=20 m
Problem- Cargo ships can cause a lot of air pollution.Solution- to use nuclear powered ships since they hold a lot of energy and can travel for long distances. How it will work is that it will need a nuclear reactor at the bottom of the boat to heat up the water and then turn it to electricity to power the boat. The boat will be made out of graphene which is a tough material to avoid any leaks in the boat. It will also contain many control rods because nuclear power is so powerful that it can create to much energy to handle. With control rods, you can slow down this process and keep it in a controlled manner. Since cargo ships are already is the ocean, there will be no need for any extra materials to make it work. -Do you think this will work? Why/Why not? -What do you think is wrong with it/ How can this be improved? Please send this to someone else I need to record 50 responses for a science project. Thank you!
Tire manufacturers recommend that you check your tire pressure monthly to avoid unnecessary tire wear and enhance safety. This is best done when the tires are cold meaning; the car has not been driven for at least 2 hours. Since you leave for work before the sun comes up you decide to inflate your tires to the recommended pressure right after you get home from work in the afternoon when the tires are still warm. What would you find if you rechecked your tire pressure after the tires have cooled down? A.Tire pressure has decreased because there is a decrease in kinetic energy of themolecules resulting in more collisions with the inside walls of the tire thusincreasing the pressure inside the tire. B.Tire pressure has increased because there is a decrease in kinetic energy of the molecules resulting in fewer collisions with the inside walls of the tire thus decreasing the pressure inside the tire. C.Tire pressure has increased because there is an increase in kinetic energy of the…
Paula has worked for Brindle Corporation for 3 years. During this time, she has worked as a machine operator/cell leader in various work cells. Recently, the plant went to mandatory 12-hour shifts and plans to remain on this schedule for several months. Paula’s present work cell is manufacturing 3-inch diameter exhaust tubes that are made from stainless steel. These tubes get a hole punched in them, a flange welded on, and burrs ground off. The pipe then gets placed into a gage to check that it was made correctly. (The tubes weigh about six pounds.) Paula has been performing the welding operation. She leans into the machine and loads the part into a fixture then positions the flange. Both pieces are clamped (using hand clamps) into position and the machine is cycled by depressing two palm buttons. The gaging operation requires placing the finished part into the gage and clamping it (using hand clamps) into place. A pin is depressed to verify the position of the hole and a…
Please solve part B only
Part 2 Set up a spreadsheet solution to this problem. This will require that you derive one formula to express the relationship between the friction coefficient, the spring constant, and the spring compression; and a second formula to find the cost of using different slide and spring types. Set up your spreadsheet as shown below. You can fill in the "Acceptable?" column manually, rather than using a formula. Turn in a copy of your spreadsheet/Matlab work (solve for $) Friction Spring Constant Spring Compression M k 0.1 0.1 0.1 0.2 0.2 0.2 50 100 150 50 100 150 4 Part 3 Your boss has decided to look at a second option. The spring mechanism will be replaced by a drop box. After leaving the slide, the blocks will travel 5 horizontal feet through the air and pass through a hole into the drop box. Using the slide you selected above, determine how far below the slide (h) to place the hole in the drop box. Yo = 5.2017/5 BLADE 2 RAMPE SLIDE 8⁰ SLIDE Acceptable? (Yes or No) $' Cost 51 In DROP…
Paula has worked for Brindle Corporation for 3 years. During this time, she has worked as a machine operator/cell leader in various work cells. Recently, the plant went to mandatory 12-hour shifts and plans to remain on this schedule for several months. Paula’s present work cell is manufacturing 3-inch diameter exhaust tubes that are made from stainless steel. These tubes get a hole punched in them, a flange welded on, and burrs ground off. The pipe then gets placed into a gage to check that it was made correctly. (The tubes weigh about six pounds.) Paula has been performing the welding operation. She leans into the machine and loads the part into a fixture then positions the flange. Both pieces are clamped (using hand clamps) into position and the machine is cycled by depressing two palm buttons. The gaging operation requires placing the finished part into the gage and clamping it (using hand clamps) into place. A pin is depressed to verify the position of the hole and a…
solve please
Using the information in the task list, calculate the duration of the project. Station 1 Processing time:5 min--> station 2 processing time 3 min--> station 3 processing time 2 min --> station 4 processing time 6 min