Time left 0:15:5SQU is trying a new particle accelerator design with a mechanical component using a spring that does not obeyHooke's law. When stretched/compressed x metres, it exerts a force of 53.6x*+69.6x(a) Compute the work required to stretch the spring from x = 0.9 m tox- 2.3 m.(b) With one end of the spring fixed, a particle of mass 3.2 kg is attached to the other end of the spring when it isstretched by an amount x = 2.3 m. If the particle is then released from rest, what is its speed at the instant the stretcin the spring isx=0.9 m?m/s(c) Is the force exerted by the spring conservative or nonconservative? Explain."NEXT PAC

U is trying a new particle accelerator design with a mechanical component using a spring that does not obey oke's law. When stretched/compressed x metres, it exerts a force of 53.6x+69.6x tho cnring from y= 0 9 m tox= 23 m

U is trying a new particle accelerator design with a mechanical component using a spring that does not obey oke's law. When stretched/compressed x metres, it exerts a force of 53.6x+69.6x tho cnring from y= 0 9 m tox= 23 m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Solve this problem using this formula: £d1mv1+£mdt = £d2mv2
a = 5 m b = 3 m c = 1 m m= 120 kgg= 9.80665 m/s^2
Find the potential energy mass of paper box=0.3 kg Height=4 m g=10 m/s2
Given the folowing mechanical system Using the energy method we are required to mathematically model the system, this achieved through the following steps. Solution 1- How many mechanical elements are in the shown in the image? 2- Fill in the given table for the kinetic and potential energies for the given example? Element Number Kinetic Energy Potential Energy U 4. 6. 3- Write the found kinetic and potential energies stated in the previous table in the following form T+U =C 4- Apply the time derivative to the found equation and find the differential equation Ə(T + U) - 0 at 5. Convert the found differential equation so that it has a unified single parameter using x= re 6- Apply the Laplace transform to the found differential equation, find the Laplace function f(s) knowing that x(0) = 0 & x(0) = 0 7- Apply the inverse Laplace transform to the f(s) equation, this is to find the final solution x(t)
Bonus Question: 8 Extra points A block of mass m = 1.0 kg is dropped from height h= 75cm onto a spring. The mass will attache to the spring and then the spring will compress. a). Find the spring constant if the maximum distance the spring is compressed is 10cm in following arrangement? ០០០០០០០០០ b). Find the maximum distance the spring is compressed in following arrangement if the angle is 30 degrees? You are using same spring. ss. mmmm 8
Plz do it carefully
Determine force in DC, HC, and HI and label if under tension or compression
Use the linear equation below to calculate Y in newtons based on X, m and b. Given Y=mX+b (Eq. 1) Ⓡ X = 49 W m = 9.7734 N hp¹¹ b = 0.745 kN NOTE: This problem has been purposely complicated by mixing metric & US Engineering units. In your own work, stick to one system if possible.
One mole of a gas obeys the Ideal Gas Law PV = 20T, where P is pressure, V is volume, and T is temperature. If the temperature T of the gas is increasing at the rate of 5 °C/s and if, when the temperature is 80 °C, the pressure P is 10N/m? and is decreasing at the rate of 2- find the m2 . s rate of change of the volume V with respect to time.
How can we solve that question I think there is mistake made !!! please I want step by step
Find the value of heat, efficiency rate, work in 68 spin and power in 0.87 seconds if an engine releases 3760 J of energy per spin and 547 J of work. Find the value of internal energy of each of the ff. given: 1. 200J of work is done on the system and 100 J of heat energy is absorbed by the system. 2.127 J of work is done by the system and 357 J of heat energy is absorbed by the surroundings. 3. A 675 J of energy is absorbed by the surroundings ang 146 J of work is done on the system.
##L2Q8 A car has the following specifications m = 1599.8kg, l = 2669.6mm, w = 1539.3mm. Assuming a1 = a2, h = 760mm, m = 0.75, get the optimal tractive force Fx1/Fx2, which reaches the optimal maximum acceleration.