Two wires of equal cross- section one made up of aluminium and other of brass are joined end to end. When the combination at wire is kept under tension the elongation in wires are found to be equal. Find the ratio of lengths of two wires. (Y = 7 × 101º N/m² and %3D AL Y = 9.1 x 1010 N/m?).
Q: A copper wire 4 m. long has diameter of 1 mm, if a load of 10 kg. wt is attached at other end. What…
A: Solution:-Given thatlength of wire (L)=4 mdiameter of wire (d)=1 mm=0.001 mmass of Load (m)=10…
Q: Compute the decrease in volume of 2.5 x 10-4 m³, of mercury when subjected to a pressure of 20 x 105…
A: Given data: mercury's volume V=2.5×10-4 m3 Pressure P=20×105 N/m2 bulk modulus β=2.8×1010N/m2
Q: 12mm dia 18mm dia. P=12 kN 2 m. 12mm dial 2. Three steel cable jointly support a load of 12kN. The…
A:
Q: Find the minimum diameter of an | = 15.1 m long tungsten wire that will stretch no more than 7.00 mm…
A:
Q: What will be the density of sea water at a depth of 1 km, if the density at the surface is 1025…
A: Correct option : (d) 1029.387 kg/m3
Q: Ex. 3: A copper metal cube has each side of length 1m. The bottom edge of cube is fixed and…
A: To find-Lateral displacement (x)=?GIven-Length of each side (L)=1 mTangential force (F)=4.2×108…
Q: A metallic bar of cross-section Ao = 103 mm² and length Lo = 0.1 mm, is subjected to = 1600 N, the…
A: Given: The cross section area of the metallic bar is 103 mm2. The original length of the…
Q: A load of 18 x 104 N is placed upon a vertical steel support of 6.0 m height and with a…
A: Given that:
Q: A copper wire of length 3 m has a diameter 1 mm. If weight of 10 kg is attached to one end of wire,…
A: We need to compute-(i) Extension produced (l)=?(ii) Lateral contraction=?The data given as-Length of…
Q: The total cross-sectional area of the load-bearing calcified portion of the two forearm bones…
A: Given: Area, A = 2.4 cm2 initial velocity, u = 80 km/h = 22.22 m/s time, t = 5 ms = 0.005 s final…
Q: A 5.25-m-long steel rod must not stretch more than 2.48 mm and the normal stress must not exceed 181…
A:
Q: f a compressional stress of 200.0 N is applied to a copper rod having a diameter of .500 cm and a…
A:
Q: Two rods of equal length 10.55 m2 anddiameter 11.7 cm2 are placed end to end. One rod is…
A: Given: Length of the rods= 10.55 m2 compressive force = 8400 N Diameter of the rod = 11,7 cm
Q: A cable hanging vertically under gravity must support its weight, w = mg, where m is the mass of the…
A: To avoid snapping of the cable, the tensile strength will be equal to the force per unit area. Write…
Q: 2.31. The three principal stresses at a given point are o=60 MPa, o2=-100 MPa, 03 =-10 MPa. If the…
A: Given: The principal stresses at a given point are 60 MPa, -100 MPa and -10 MPa. Introduction: The…
Q: Question 16: A cubical solid aluminium (bulk modulus = -V (dP/dV) = 70 GPa) block has an edge length…
A: Given that, Bulk modulus=-VdPdV=70 GPa Here we know that, B=VdPdV
Q: Q. 29: A wire of length (L) and radius (r) is loaded with a weight (Mg). If (Y) and (o) denote the…
A:
Q: A 8-mm-thick rectangular alloy bar is subjected to a tensile load P by pins at A and B, as shown in…
A:
Q: A research scientist would like to estimate the tensile strength of a newly created synthetic fiber.…
A: SOlution:
Q: copper wire of length 3 m nas a diameter 1 mm. If weight of 10 kg is attached to one end of wire,…
A: To find- (1) Extension produced (l)=? (2) Lateral contraction =? Given- Length of wire (L)=3 m…
Q: A farmer making grape juice fills a glass bottle to the brim and caps it tightly. The juice expands…
A: thank you
Q: A body of mass 500 kg is suspended at the free end of an iron wire of length 3 m and cross-sectional…
A:
Q: A short timber post of rectangular section has one side twice the other. It contracts by 0.05 cm/m.…
A:
Q: 1.18 A load P is applied to a steel rod supported as shown by an alu- minum plate into which a…
A: l=12 mm sheering stress=180mPa The Stress of an aluminum plate: 70mPA
Q: 5-77. The steel shaft has a diameter of 40 mm and is fixed at its ends A and B. If it is subjected…
A: Diameter of steel shaft , d = 40mm The applied force, F= 3kN Rigidity modulus of the shaft, Gst =…
Q: A 1.05-m-long rod of negligible weight is supported at its ends by wires A and B of equal length…
A: This question involves two concepts: (A) Free body diagram and subsequent condition for the static…
Q: A copper wire 4 m long has diameter of 1 mm, if a load of 10 kg. wt is attached at other end. What…
A: We need to compute-(a) extension (l)=?(b) Lateral compression=?Given that-Length of wire (L)=4…
Q: The table below shows ultimate tensile strengths (Fu ) and Young's moduli (Y) for tungsten (W) and…
A:
Q: One end of a wire 2 m long and 02 cm in cross-section is fixed in a ceiling and a load of 4:8 kg is…
A:
Q: You apply a force of magnitude F1 to one end of a wire and another force F in the opposite direction…
A: Newton's second law of motion relates the net force acting on the object to the acceleration…
Q: Problem 1: A cold drawn C-1025 steel rod of circular cross section is subjected to a variable…
A:
Q: A copper wire of length 2.2m and a steel wire of length 1.6m both of diameter 3.0mm, are connected…
A:
Q: The homogeneous 40-kg basr ABC is held by a horizontal rope attached to end C. Neglecting friction,…
A: Given : mass m = 40 kg ω = mg = 40×9.81 = 392.4 N
Q: A steel wire of length 1.40 m and diameter 1.00 mm is joined to an aluminum wire of identical…
A: We are given the mass of object. We can thus find the force acting on wire. We then find the stress…
Q: Two wires A and B are of the same length. Their diameters are in the ratio 1:2 and the Young's…
A: We need to compute-Ratio of elongations produced eAeB=?The data given as-Length of wire A=Length of…
Q: An axial load Pis applied to the rectangular bar shown. The cross-sectional area of the bar is 216…
A: Answer: Normal stress, σ =2.73×108 N/m2 Shear stress, τ =1.51×108 N/m2
Q: Consider a metal bar of length L, cross-sectional area A, and Young's modulus Y. When a tension…
A:
Q: A fishing rope of length (74+ 50) m has the diameter (74 + 5) mm. When a weight of (74 +200) N is…
A: i. The cross-sectional area of the rope is given by,
Q: Referring to Fig. compute the maximum force P that can be applied by the machine operator, If the…
A:
Q: Steel construction beams, with an industry designation of "W12 x 25," have a weight of 25 pounds per…
A: Disclaimer: “Since you have asked multiple question, we will solve the first question for you. If…
Q: A rigid bar of mass M is supported symmetrically by three wires each of length l. Those at each end…
A:
Q: brass rod with a length of 1.40 m and a cross. sectional area of 2.00 square cm is fastened end to…
A: brass rod with a length of 1.40 m and a cross. sectional area of 2.00 square cm is fastened end to…
Q: Two structural members A and B are bolted to a bracket as shown. Knowing that both members are in…
A: Given-Compression force in A, Compression force in B, Free Body Diagram -
Q: 75 kN Composite A-36 steel bar shown made from two segments AB and BD. Area A= 600 mm² and App=1200…
A: Write the given values of this problem. AAB=600 mm2ABD=1200 mm2
Q: Find the elongation of a rod made of aluminum and copper under a tension of 5.8×103 N. The…
A: Given information: Here, R is the radius of the rod, T is the tension, LAl and LCu are the length…
Step by step
Solved in 2 steps