Two vertical forces, each of magnitude P= 14 kips, are applied to a beam of the cross section shown. Determine the maximum tensile and compressive stresses in portion BC of the beam. 3 in. 3 in. 3 in. 6 in. 2 in. P. C D -60 in.→ 40 in. 40 in. The maximum tensile stress is |ksi. |ksi. The maximum compressive stress is

Two vertical forces, each of magnitude P= 14 kips, are applied to a beam of the cross section shown. Determine the maximum tensile and compressive stresses in portion BC of the beam. 3 in. 3 in. 3 in. 6 in. 2 in. P. C D -60 in.→ 40 in. 40 in. The maximum tensile stress is |ksi. |ksi. The maximum compressive stress is

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.4.8P: - A specimen used in a coupon test has norm al stress ??. = 15 MPa (see figure). Using Mohr’s...

See similar textbooks

Similar questions

The stresses on an element are sx= 1000 Psi. sy= 500 psi, and txy= 350 psi. Find the stresses acting on an element oriented at an angle 0 = 250. Show these stresses on the rotated element.
- A specimen used in a coupon test has norm al stress ??. = 15 MPa (see figure). Using Mohr’s circle, find the state of stress on the element oriented at angle ? = 20° and show the full stress state on a sketch of a properly oriented element.
Two vertical forces, each of magnitude P= 26 kips, are applied to a beam of the cross section shown. Determine the maximum tensile and compressive stresses in portion BC of the beam. 8 in. 1 in. 1 1 in.- 6 in. 1 in. 4 in. P P A D 60 in. 20 in. 20 in. The maximum tensile stress is ksi. The maximum compressive stress is ksi.
Two vertical forces, each of magnitude P= 28 kips, are applied to a beam of the cross section shown. Determine the maximum tensile and compressive stresses in portion BC of the beam. 8 in.→ 1 in. 1 in.- 6 in. 1 in. B 4 in. P C D 60 in. 20 in. 20 in. The maximum tensile stress is ksi. The maximum compressive stress is ksi.
The horizontal cross-section of the cast-iron standard of a vertical drilling machine has the form shown. The line of thrust of the drill passes through P. Find the greatest value the thrust may have without the tensile stress exceeding 15 MN/m2. What will be the stress along the face AB? (Cambridge) 12.4 19.0cm A 36 cm 1.60 cm 1.90 cm 1.60 cmT B. +17.5cm
Two forces are applied on the beam shown below. (a) Determine the normal and shear stresses at point B on the shown cross-section. (b) Show the state of stress at the point B on a volume element. 400 lb B 1 in. 2 in. 500 Ib 2 in 10 in. 1.5 in. 1.5 in. Show your steps and highlight the following answers please I =
An axial load Pis applied to the rectangular bar shown. The cross-sectional area of the bar is 398 mm2. Determine the normal stress perpendicular to plane AB and the shear stress parallel to plane AB if the bar is subjected to an axial load of P = 88 kN. Assume a = 61°. a B Answers: The normal stress o = MРа. The shear stress T = i MРа.
Q1 / If the cross section of the femur can be approximated as a circular tube, determine the state of stresses on the points A and B at section due to the loads as shown in figure Q1. T. = 2 cm = 1.6 cm %3D Figure Q1 B L 20 cm
Figure shows a beam made from bronze subjected to a 3.5kN.m bending couple and its respective tensile properties. i) With aid of illustration, draw the deformation of the bean and locate the position where the beam experience maximum tensile stress (αmax)t and maximum compressive stress (αmax)c. Accordingly. Determine the magnitude of these two stresses. ii) Sketch the two-dimensional stress distribution acting on point A and point B over the cross-sectional area of the beam as observed from side view. Estimate the magnitude of the stresses at those two points.
Two vertical forces, each of magnitude P= 28 kips, are applied to a beam of the cross section shown. Determine the maximum tensile and compressive stresses in portion BC of the beam. l8 in. 1 in. 1 in. 6 in. 1 in. 4 in. B D 60 in. 20 in. 20 in. ksl. The maximum tensile stress is The maximum compressive stress is ksi.
A 70 lb force P is applied to the brake pedal of a tractor, as shown below. Force Qis applied to the brake cylinder. Determine the maximum tensile and compressive normal stresses on section a-a, which is midway between points A and B. Section a-a is a x 1 in rectangle. 3 16 8.5 in 7.5 in P 30% 1 in a A B -4 in- a -Q
I The cross-sectional area of each member of the truss is 1200 mm". Calculate the stresses in members CD and BC. State whether the stresses (in MPa) are tensile or compressive. 300 kN 300 kN 6m 4 m 4 m C 3m E 3m 100 kN 200 KN