Two vertical forces are applied to a simply supported beam, having the cross section shown. Assume LAB=LCD=1.3 m, LBc-3.3 m, P=16 kN, b-180 mm, t-17 mm, tw-11 mm, d=167 mm. Determine the maximum tension (a positive number) and compression (a negative number) bending stresses produced in segment BC of the beam. Answers: maxT = maxC = LAB P B 252.629 i 73.79 LBC bf → w Cross section MPa MPa LCD X

Two vertical forces are applied to a simply supported beam, having the cross section shown. Assume LAB=LCD=1.3 m, LBc-3.3 m, P=16 kN, b-180 mm, t-17 mm, tw-11 mm, d=167 mm. Determine the maximum tension (a positive number) and compression (a negative number) bending stresses produced in segment BC of the beam. Answers: maxT = maxC = LAB P B 252.629 i 73.79 LBC bf → w Cross section MPa MPa LCD X

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Two vertical forces are applied to a simply supported beam, having the cross section shown. Assume LAB=LCD=2.0 m, LBc=6.9 m, P=19 kN, bf=180 mm, t₁=14 mm, tw=9 mm, d=159 mm. Determine the maximum tension (a positive number) and compression (a negative number) bending stresses produced in segment BC of the beam. A Answers: OmaxT maxC = LAB i i P B LBC bf + Cross section MPa MPa P LCD D X
A simple pin-connected truss is loaded and supported as shown. All members of the truss are aluminum pipes that have an outside diameter of 47 mm and a wall thickness of 7 mm. Determine the normal stress in each truss member. Assume P = 15 kN, Q = 26 kN, a = 1.1 m, b = 2.5 m, and c = 2 m. Use positive for tensile stress and negative for compressive stress. Answers: OAB = OAC = OBC= i B (3) b MPa. MPa. MPa.
Two vertical forces are applied to a simply supported beam, having the cross section shown. Assume LAB=LCD=1.9 m, LBc=5.4 m, P=13 kN, b=190 mm, t-13 mm, tw-8 mm, d=158 mm. Determine the maximum tension (a positive number) and compression (a negative number) bending stresses produced in segment BC of the beam. Answers: OmaxT = omaxC = LAB i tel i LBC bf HI Cross section MPa MPa P LCD
The beam is loaded by two point forces P. The beam is assembled according to the cross-sectional view by nailing wooden parts with cross-sections of 50 mm x c = 220 mm and 25 mm x d = 260 mm. How large can the value of the load P be when the distance between the nails in the longitudinal direction of the beam is 100 mm, the cross-sectional area of the nail is 9 mm2 and their permissible shear stress is 110MPa? Then calculate the maximum stresses and shear stresses of the beam at that load when the distance between the articulated supports is L = 1.9 m and the length of the beam projections a = 1.3 m. Permissible shear force of one nail? kN Static torque of the cutting surface? mm^3 Maximum torque change in cantilever? kNm Cutting force of the projection? kN Magnitude of force P? kN Calculated with the obtained force P maximum normal stress? MPa shear stress maximum? MPa
d = 600 6Ø28 75 75 300 can you please show how to find the elastic stress and design ratio? fc' = 27 MPa; M1 = 60 KN-m; M2 = 200 KN-m
P = 9 kip 2 in. 1 in. 1.5 ft The aluminum post shown in the figure is reinforced with a brass core. If this assembly supports an axial compressive load of P = 9 kips applied to the rigid cap, determine the average normal stress in the aluminum and the brass. Take Eal=10103ksi and Ebr= 15103ksi.
A pin-connected truss is loaded and supported as shown. Each aluminum member has a cross-sectional area of A = 2.2 in.². Assume a = 4.00 ft and b = 4.80 ft. If the normal stress in each member must not exceed 45 ksi, determine the maximum load Pmax that may be supported by the structure. Answer: Pmax= b 41250.16 B E b kips
A simple pin-connected truss is loaded and supported as shown. The load Pis 240 kN. All members of the truss are aluminum pipes that have an outside diameter of 130 mm and a wall thickness of 14 mm. Determine the normal stress in each truss member. Assume truss dimensions of a = 10 m, b = 6.25 m, and c= 5 m. Tensile stress is positive, while compressive stress is negative. b D Answer: OAB 11 JAC OBC= OBD = OCD = i M M a B MPa MPa MPa MPa MPa
A beam having the cross section shown is subjected to a couple M0 acting in a vertical plane. Determine the largest permissible value of the moment M0 of the couple if the maximum stress is not to exceed 103 MPa. Given: Iy = Iz = b4/36 Iyz = b4/72
Determine the maximum tensile stress and maximum compressive stress due to the load P acting on the simple beam AB (see figure). Data are as follows: P= 5.4 kN L=3.0 m d=1.2 m b=75 mm t_=25 mm h=100 mm h1=75 mm c1=62.5 mm c2=37.5 mm, and l= 3.3203x10⁶ mm⁴
A simple pin-connected truss is loaded and supported as shown. The load P is 160 kN. All members of the truss are aluminum pipes that have an outside diameter of 130 mm and a wall thickness of 9 mm. Determine the normal stress in each truss member. Assume truss dimensions of a = 6 m, b = 3.75 m, and c = 3 m. Tensile stress is positive, while compressive stress is negative. b D A Answer: OAB OAC = OBC OBD OCD || || II a MPa MPa MPa MPa MPa B C
Determine the shear stress at points: A, B. C, D and E in beam shown in Figure 5. Take E-30 GPa