#11Normal stress in rods 1 and 2 A(1)B(2)C Two solid cylindrical rods (1) and (2) arejoined together at flange B and loaded, asshown. The diameter of rod (1) is d1= 1.98 in. and the diameter of rod (2) is d2%3D= 3.16 in. Determine the normal stresses inrods (1) and (2). Assume P = 12 kips and Q= 34 kips. Use positive for tensile stressand negative for compressive stress.%3D

Answered: Image /qna-images/answer/c0d3cf7d-e55d-4565-b355-85f50587db89.jpg

Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded, as shown. The diameter of rod (1) is di = 1.98 in. and the diameter of rod (2) is d2 %3D = 3.16 in. Determine the normal stresses in rods (1) and (2). Assume P = 12 kips and Q %3D = 34 kips. Use positive for tensile stress %3D and negative for compressive stress.

Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded, as shown. The diameter of rod (1) is di = 1.98 in. and the diameter of rod (2) is d2 %3D = 3.16 in. Determine the normal stresses in rods (1) and (2). Assume P = 12 kips and Q %3D = 34 kips. Use positive for tensile stress %3D and negative for compressive stress.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The thin rectangular plate is uniformly deformed such that Ex = 220E, Ey= -680 uE, and yy = 870 urad. If a = 35 mm, determine (a) the normal strain &, in the plate. (b) the normal strain &, in the plate. (c) the shear strain ynt in the plate. B D. a a a a a a a a a Answers: (a) En= i HE (b) Et= i HE (c) Ynt = i prad
A magnesium-alloy rod (E = 6.5 x 10 ksi) of Prob. 3.4-6. diameter d 1 in. is encased by a brass tube (E 15 x 10 ksi) with outer diameter d. = 1.5 in.; both have length. L = 20 in. An axial load P = 10 kips is applied to the resulting bimetallic rod. (a) Determine the normal stresses and , in each material, assuming that the magnesium rod and brass tube are securely bonded to each other. (b) Determine the elongation of the bimetallic rod. P
The wire BC has a diameter of 0.175 in. and the material has the stress-strain characteristics shown in the figure. Determine the vertical displacement of the handle at D if the pull at the grip is slowly increased and reaches a magnitude of (a) P= 480lb, (b) P= 700lb. Assume the bar is rigid.
A flat bar of a width b = 60 mm and thicknesst = 10 mm is loaded in tension by a force P (seefigure). The bar is attached to a support by a pin ofa diameter d that passes through a hole of the samesize in the bar. The allowable tensile stress on the netcross section of the bar is σT = 140 MPa, the allowableshear stress in the pin is τS = 80 MPa, and theallowable bearing stress between the pin and the baris σB 5 200 MPa.(a) Determine the pin diameter dm for which theload P is a maximum.(b) Determine the corresponding value Pmax of theload.
4.15 Knowing that for the casting shown in the figure the allowable stress is 6 ksi in tension and 15 ksi in compression, determine the maximum couple M that can be applied.
Q2: For the stresses at the point shown, find: • The maximum shearing stress. • The principal stresses and planes. 12 ksi 8 ksi 6 ksi
A steel pipe is subjected to the 16-kN load shown below. Its outside diameter is 140 mm and its thickness is 7 mm. Consider that the yield strength of steel is 240 MPa. Analyze point H ONLY. Due to the pressure in the pipe, there is an 11.25-MPa (T) normal stress along x and a 22.50-MPa (T) normal stress along z of point H. A. Determine the internal forces and moments at the pertinent section through an FBD. B. Determine the stresses experienced by point H. Illustrate using a stress element. C. Determine the FS by MSST at point H D. Determine the von Mises equivalent stress at point H E. Determine the FS by MDET at point H 700 mm 16 KN 1,300 mm
Rigid bar ABCD is loaded and supported as shown. Steel [E = 28400 ksi] bars (1) and (2) are unstressed before the load P is applied. Bar (1) has a cross-sectional area of 0.82 in.² and bar (2) has a cross-sectional area of 0.41 in.². After load P is applied, the strain in bar (1) is found to be 700 μe. Assume L₁=69 in., L₂-89 in., a=34 in., b=33 in., and c-37 in. Determine: (a) the stresses in bars (1) and (2). (b) the vertical deflection VD of point D on the rigid bar. (c) the load P. A Answers: (a) 0₁ = (b) VD = (c) P= i i i L₁ a (1) B L2 b ksi, 0₂ = in. kips. (2) C i D P ksi.
Rigid bar ABCD is loaded and supported as shown. Steel [E = 30000 ksi] bars (1) and (2) are unstressed before the load P is applied. Bar (1) has a cross-sectional area of 0.75 in.2 and bar (2) has a cross-sectional area of 0.425 in.2. After load P is applied, the strain in bar (1) is found to be 780 μs. Assume L₁-60 in., L₂=90 in., a=40 in., b=40 in., and c-30 in. Determine: (a) the stresses in bars (1) and (2). (b) the vertical deflection vp of point D on the rigid bar. (c) the load P. A Answers: (a) 0₁ = (b) VD= (c) P = i i i L₁ a L2 in. (2) ksi, 0₂ = i kips. C D P ksi.
! Required information Consider the given state of stress. A 16 ksi 10 ksi Determine the normal and shearing stresses after the element shown has been rotated through 15° clockwise, using Mohr's circle. The normal stress Ox'is - |ksi and Oy'is ksi. The shearing stress Tx'y'is ksi.
Problem 2 The rigid bar is plnned at A and held by two flexible bars at E and C. The load P Is applled at B. The two flexible bars FE and DC each have a diameter of 1 In. The flexible bars are elastic- perfectly plastic with a yleld stress equal to 20 ksl and a yleld strain of 0.001. Determine the following: The load R, at first yleld and the corresponding deflection at B, &, The ultimate load Pu and the corresponding deflection du The permanent deflection and residual stresses in each rod if the ultimate load is removed Construct P - A curve showing yield, ultimate and permanent deformation o (ksi) 1 ft E F 1 ft1 ft 20 B P e (in./in.) 0.001 1 ft D 2 ft 1 ft A
Rigid bar ABCD is loaded and supported as shown. Steel [E = 30000 ksi] bars (1) and (2) are unstressed before the load P is applied. Bar (1) has a cross-sectional area of 0.75 in.² and bar (2) has a cross-sectional area of 0.425 in.². After load P is applied, the strain in bar (1) is found to be 780 μe. Assume L₁-60 in., L₂=90 in., a=40 in., b=40 in., and c=30 in. Determine: (a) the stresses in bars (1) and (2). (b) the vertical deflection VD of point D on the rigid bar. (c) the load P. Answers: (a) σ₁ = (b) VD = i (c) P = Mi i L₁ a (1) B L2 b in. C ksi, 0₂ = i kips. с tel D P ksi.