Two same size PV Modules are connected in Parallel. The specification of each module is given as, Number of cells = 36, Area of each cell is 12 cm x 12 cm. Assume the necessary data. Refer to the above PV Panel choose the correct statement. a. The output current of each PV Module is 2.15A b. The output current of each PV Module is 8.6A c. The output current of each PV Module is 4.3A d. The output current of each PV Module is 1.25A

Two same size PV Modules are connected in Parallel. The specification of each module is given as, Number of cells = 36, Area of each cell is 12 cm x 12 cm. Assume the necessary data. Refer to the above PV Panel choose the correct statement. a. The output current of each PV Module is 2.15A b. The output current of each PV Module is 8.6A c. The output current of each PV Module is 4.3A d. The output current of each PV Module is 1.25A

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter30: Dc Motors

Section: Chapter Questions

Problem 6RQ: What is CEMF?

See similar textbooks

Similar questions

A charging circuit that will deliver constant DC current will be designed. The input of the circuit is 220V / 50Hz AC and its outputIt will be 5V / 2A DC.The circuit will consist of 3 parts:AC transformer will reduce the voltage on the inputii. AC rectifier circuit will convert low AC voltage to DCiii. Current source, this part will keep the current at the output constant.You determine the transformer drop rate in the first part. Its output is low voltage ACas the source and design the second and third parts accordingly.
Do calculation. This is not a simulation problem
1) AC power in a load can be controlled by using a. Two SCR's in parallel opposition b. Two SCR's in series c. Three SCR's in series d. Four SCR's in series 2) The advantage of using free - wheeling diode in half controlled bridge converter is that a. There is always a path for the ac current independent of the ac line b. There is always a path for the dc current independent of the ac line c. There is always a path for the dc current dependent of the ac line d. There is always a path for the ac current dependent of the ac line 3) Silicon controlled rectifier can be turned on a. By applying a gate pulse and turned off only when current becomes zero b. And turned off by applying gate pulse c. By applying a gate pulse and turned off by removing the gate pulse d. By making current non zero and turned off by making current zero
In a rectifier circuit , DC output voltage and RMS output voltage is 0.3 V & 0.48 V respectively. The form factor of this circuit is ___________________.
I have one (1) AC source, four (4) diodes, and one (1) thyristor. In this case, I would like to obtain a full- controlled rectifier using these components; please describe the circuit?
In a linear power supply, where will you connect the capacitor on order to reduce the ripple output of a rectifier circuit? O in parallel with the transformer O in series with the transformer O in parallel with the load resistor O in series with the load resistor
A 120 Vp is applied to the primary coil of a center-tap transformer of turn ratio (n1 : n2 = 6: 2) . If the secondary coils are connected to a Ge diodes center-tap full wave rectifier, the output DC voltage is about __________. *1- 13.42 V2- 14.15 V3- 15.58 V4-12.54 V5- 16.23 V
What is Basic Circuit element
In the circuit in the figure, an AC voltmeter will be made with full wave rectifier circuit structure. R = 50ohm and diodesResistance values in the direction of transmission are Rd = 100ohm. Inside of the DC ammeter to be used as indicatorthe resistance is very, very small. The AC mark to be measured is Vs = 100 Sinwt Volts.a- Draw the shape of the current passing through the DC Ammeter and calculate its maximum value.b- Find the average value of the current passing through the DC Ammeter.c- Analyze the voltage seen at the ends of diode D1 for both alternans.d- Find the Rms value of the voltage seen at the ends of the diode D1.
Two silicon diodes are connected in parallel and in series with resistor 0.33kohms and a battery of 10V. the voltage across the resistor 0.33k ohms is ___. The current flowing through resistor 0.33K ohms is approximately equal to___. The current of one diode is___.
Can anyone help me with this circuits question. I don’t need the design of the BW LPF just the hand calculations. Thank you
Which of the following statements about bridge tip rectifiers is false? A) If the 1-phase type has source inductance, the average value of the output voltage is lower than in the absence of the inductance. B) The average output voltage value of the 1-phase type is 0.9 times the peak voltage of the network. C) none D) There are only odd harmonics in the current drawn by the 1-phase type from the mains. E) The average value of the output voltage of the 3-phase type is larger as the 3-phase and 1-phase types are compared