Two plates with a thickness of 35 mm, width of 160 mm, and length of 200 mm are joined together by a pin with a diameter of 60 тm. 200 mm 60 mm P P 0 mm 160 m | 35 mm 35 mm 200 mm 1) For a Factor of Safety of 2, find the maximum load P that can be applied if the bearing strength of the plate is 250 M Pa and the shear strength of the pin is 100 MPa.

Two plates with a thickness of 35 mm, width of 160 mm, and length of 200 mm are joined together by a pin with a diameter of 60 тm. 200 mm 60 mm P P 0 mm 160 m | 35 mm 35 mm 200 mm 1) For a Factor of Safety of 2, find the maximum load P that can be applied if the bearing strength of the plate is 250 M Pa and the shear strength of the pin is 100 MPa.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.7.10P: Three round, copper alloy bars having the same length L but different shapes are shown, in the...

See similar textbooks

Similar questions

Solve the preceding problem if the internal pressure is 3,85 MPa, the diameter is 20 m, the yield stress is 590 MPa, and the factor of safety is 3.0. (a) Determine the required thickness to the nearest millimeter. (b) If the tank wall thickness is 85 mm, what is the maximum permissible internal pressure?
Three round, copper alloy bars having the same length L but different shapes are shown, in the figure. The first bar has a diameter d over its entire length, the second has a diameter d over one-fifth of its length, and the third has a diameter d over one-fifteenth of its length. Elsewhere, the second and third bars have a diameter Id. All three bars are subjected to the same axial load P. Use the following numerical data: P = 1400 kN, L = 5m,d= 80 mm, E= 110 GPa. and v = 0.33. (a) Find the change in length of each bar. (b) Find the change in volume of each bar.
Consider the copper lubes joined in the strength of the copper is err = 200 MPa, figure using a "sweated" joint. Use the properties and what is the maximum load P]iwathat can be dimensions given. applied to the joint if the desired factor of safety in shear is FS_ - 2 and in tension is (a) Find the total elongation of segment 2-3-4 (
A bracket is supported by means of 4 rivets of the same size. Design the diameter of the rivet if C, (tensile ultimate stress) for the rivet material is 560MPA. Which of the rivet has max resistance? 20N 20kN 30 nm so nm 30 mm 1.
Two plates each with thickness of 18 mm are bolted together with 6 – 20mm ø bolts forming a lap connection. Bolt spacing are as follows: X1 = 50 mm, X2 = 120 mm and X3 = 100 mm FvRivet = 130 MPa. Calculate the the pemissible tensile load P under the following conditions. a. Based on the effective net area. b. Based on block shear. c. Based on the safe value of P.
Q1/ A bracket is supported by means of 4 rivets of the same size. Design the 7. Alalkau diameter of the rivet if Ou (tenşile ultimate stress) for the rivet material is 560MPA. Which of the rivet has max resistance? 20KN 20KN B0mm 30 mm 30 mm 30 mm
The one end of a hollow square bar whose side is 10.50 in with 1.50 in thickness is under a tensile stress and the other end is connected with a U bracket using a double-pin system. Find the minimum diameter of pin is used according to shear strength. Take the factor of safety as 1.5 and σallowable=243 ksi for pin material.
Let's considera rod having a solid circular cross-section with diameter of 4 mm and it is made of a material having a Young's modulus E= 200 Gpa and a Poisson's ratio of 0.3. If a tensile force Fis subjected to that rod cross-section, the diameter becomes 3.995 mm. determine the applied force F Select one: OF 5236 N O F=15708 N Clear mopshoe Finish attempt
two plates are fastened by a number of rivets and a tensile load of 300 KN is applied, find the number of rivets required if the shearing stress is limited by 65 MPa, and the bearing stress is limited by 95 ?MPa 300 KN 300 KN 125 mm 30 mm Dia. 25 mm 300 KN 25 mm 300 KN
The figureshows a copper rod that is placed in an aluminum tube. The rod is 0.005 in. longer than the tube of length L = 10.77 in. Find the maximum safe load P (in lb with four decimal places) that can be applied to the bearing plate, using the following data: area of copper = 2.09 sq, in. area of aluminum = 3.13 sq, in. E of copper = 17082712 ksi E of aluminum = 10068197 ksi allowable stress for copper = 19884 ksi allowable stress for aluminum = 10200 ksi
The one end of a hollow square tube whose side is 10 in with 1 in thickness is under a tensile stress 102,500 psi and the other end is connected with a U bracket using a double-pin system. Find the minimum diameter of pin is used according to shear strength. Take the factor of safety as 1.5 and σ(allowable stress) = 243 ksi for pin material.
Rigid member AC is supported by a pin at A and the vertical steel link BD as shown. The diameter of the link and its length are given in the table below for cach student. The alloawble stress of link BD is 200 MPa. a) Determine the maximum possible value of the load P b) If P-90 kN, determine the change in temperature needed for link BD to have no change in length. Given Me=12*10/"C, E,200 GPa B A 0.4m 0.2m