Two kg of air, initially at 500 kPa, 350K, and 4 kg of carbon monoxide (CO) initially at 200kPa, 450K are inside a rigid, well-insulated container and separated by a partition as shown in figure below. The partition is released to move freely and allow the transfer of heat from one gas to the other without energy storage in the partition itself. The air and CO each behave as ideal gases with constant specific heats (CVo) of 0.717kj/kg-k and 0.744 kj/kg-k and gas constants (R) of 0.287 kJ/kg-k and 0.2968 kJ/kg-k, respectively. The heat is transferred from one gas to another until both gasses reach the same final pressure and temperature. At this equilibrium state determine: (m³) A. Total volume of the container: V =

Two kg of air, initially at 500 kPa, 350K, and 4 kg of carbon monoxide (CO) initially at 200kPa, 450K are inside a rigid, well-insulated container and separated by a partition as shown in figure below. The partition is released to move freely and allow the transfer of heat from one gas to the other without energy storage in the partition itself. The air and CO each behave as ideal gases with constant specific heats (CVo) of 0.717kj/kg-k and 0.744 kj/kg-k and gas constants (R) of 0.287 kJ/kg-k and 0.2968 kJ/kg-k, respectively. The heat is transferred from one gas to another until both gasses reach the same final pressure and temperature. At this equilibrium state determine: (m³) A. Total volume of the container: V =

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A tank of compressed air is at 40°C and 10 atm. 1 third of the gas is removed for inflating a car tire. The tank is allowed to exchange heat with the surroundings to maintain its temperature at all times. What kind of a process is this? What is the pressure remaining in the tank? a. Sketch the problem. b.Draw lines identifying the control volume, or control mass. c.Identify the states with numbers, letters, or descriptions such as “in” and “out”. d.Write down the knowns and unknowns. e.Identify what is being asked for. f.State all assumptions.
As shown in the figure, a tank fitted with an electrical resistor of negligible mass holds 2 kg of nitrogen (N₂), initially at 27°C, 0.1 MPa. Over a period of 20 minutes, electric power of 0.28 kW is provided to the resistor. During this same period, a heat transfer of magnitude 10.5 kJ occurs from the nitrogen to its surroundings. Assume ideal gas behavior, but do not assume constant specific heats. Step 1 Determine the final temperature, in °C, and the final pressure, in MPa. Determine the final temperature, in °C. T₂= i Save for Later Nitrogen, N₂ m = 2 kg T₁ = 27°C P₁ = 0.1 MPa °℃ Qout, 12 = 10.5 kJ É electric Attempts: 0 of 5 used Step 2 The parts of this question must be completed in order. This part will be available when you complete the part above. Submit Answer
As shown in the figure, a tank fitted with an electrical resistor of negligible mass holds 2 kg of nitrogen (N₂), initially at 27°C, 0.1 MPa. Over a period of 15 minutes, electric power of 0.12 kW is provided to the resistor. During this same period, a heat transfer of magnitude 10.5 kJ occurs from the nitrogen to its surroundings. Assume ideal gas behavior, but do not assume constant specific heats. Nitrogen, N₂ m = 2 kg T₁ = 27°C P₁ = 0.1 MPa +0000000* Qout, 12 = 10.5 kJ Determine the final temperature, in °C, and the final pressure, in MPa. É electric
1. An ideal gas with R = BTU 0.062- and Cy =0.158 BTU undergoes a three Ibm-°R process cycle in aclosed system. From the initial state of 20 psia and 570 °R, the gas is compressed at constant temperature to 1/5 of its initial volume, process 1-2; it is then heated isochorically to state 3,process 2-3; and finally, it expands polytropically with index n= 1.5 back to its initial state, process 3-1. Determine the pressures, specific volumes and temperatures at eardinal points around the cycle and the cycle thermal efficiency.
While the temperature remains constant at 38 degrees C, 2.5 kg of a certain ideal gas whose Cp = 1.1724 kJ/kg-K, Cv = 0.8375 kJ/kg-K rejects 300kJ of heat. If the initial pressure 596kPa, find: (ANSWER MUST BE EXACT TO CHOICES) (a) the final pressure in kPa CHOICES 1,887 1,792 1,682 (b) the initial volume in cubic meter CHOICES 0.44 0.48 0.46 (c) the final volume in cubic meter CHOICES 0.155 0.145 0.138
Air as an ideal gas is contained in a piston/cylinder system constrained by a non-linear spring. Initially the gas in the cylinder is at 100 kPa, which is balanced by the atmospheric pressure outside of the cylinder (the weight of the piston is negligible). The force on the spring at the start is zero. The spring force is F=kx². k=600. kNt/m². The cross-sectional area of the piston is 1 m², the initial volume is 1 m³, and the initial temperature is 300 K. Heat is added until the volume of the gas has expanded to 1.5 m³. Find: (a) The work done by the gas on the face of the piston (kJ). (b) The final temperature (K). (c) The amount of heat added (kJ). Hint: This problem is easiest if you calculate the spring work and the atmospheric work separately. Air V₁=1.0 m³ Piston Area = 1.0 m² T₁=300 K P₁=100 kPa Atmospheric P on upper piston face= 100 kPa
Initially 3 kg of saturated water mixture at 300 kPa with a quality of 0.8 is contained in a piston-cylinder device. The water is heated at a constant pressure until the temperature reaches 500°C. Use the properties for water on the second the third pages of the equation sheet. a. Find the work done during the process. b. Find the change in internal energy of the water. c. Find the heat transfer during the process. Is heat added or removed from the system?
b) As shown in Figure A2-b, an insulated rigid container holds 1.4 kg of saturated water and air. At the initial state, the temperature of the saturated water is 210°C and 75% of the volume is occupied by air and the rest by the saturated liquid. An electric heater inside the container heats the water and converts to saturated vapor after 0.333 hours. Air Water 1.4kg, 210°C Figure PLEASE TURN OVER (i) Determine the volume of the container in m³. (ii) Determine the temperature of the saturated vapor (iii) Determine the power of the resistor
While the temperature remains constant at 38 degrees CELSIUS, 2.5 kg of a certain ideal gas whose Cp = 1.1724 kJ/kg-K, Cv = 0.8375 kJ/kg-K rejects 300kJ of heat. If the initial pressure 566kPa, find: (ANSWER MUST BE EXACT TO CHOICES) (a) the final pressure in kPa CHOICES 1,887 1,682 1,792 (b) the initial volume in cubic meter CHOICES 0.48 0.44 0.46 (c) the final volume in cubic meter CHOICES 0.145 0.138 0.155
An insulated cylinder-plunger device with a constant load contains 2 L of saturated liquid water at a temperature of 80 °C . A paddle wheel agitates the water, contributing 500 kJ to the system, while for 10 min a current of 8 A passes through a 110 V resistor placed in the water. It is correct to state: I) Information is missing to calculate the moving boundary work. II) The final state is a vapor-liquid mixture at 47.42 kPa. III) In the final state, the volume is equal to 0.781 m3/kg IV) The sum between the electric work and the work of the paddlewheel is equal to hfg
Refrigerant R-134a vapor in a piston-cylinder assembly, it is increased to 50°C under constant pressure operation from 8 bar saturated steam. Calculate the work and heat transfer per unit mass for refrigerant. (kJ/kg) Changes in kinetic and potential energy can be neglected.
A mass of 5 kg of saturated liquid-vapor mixture of water is contained in a piston- cylinder device at 100 kPa. Initially, 2 kg of the water is in the liquid phase and the rest is in the vapor phase. Heat is now transferred to the water, and the piston, which is resting on a set of stops, starts moving when the pressure inside reaches 200 kPa. Heat transfer continues until the total volume increases by 30 perrems Determine a) the initial and final temperatures, b) the mass of liquid water when the piston first starts moving, and c) the work done during this process. H20 m = 5 kg