solve show all steps Two identical 4 in. major-diameter power screws (single-thread) with modified square threads areused to raise and lower an 70 ton sluice gate on a dam. Quality of construction and maintenance(including lubrication) are good, resulting in an estimated friction coefficient of only 0.1 for thescrews. The thrust collars for the power screws have a mean diameter of 5.50 in and an effectivefriction coefficient of 0.24. Assuming that, because of gate friction, each screw must provide alifting force of 36.4 tons, what power is required to drive each screw when the gate is being raisedat the rate of 3 ft/min? Also, what is the corresponding rotational speed of the screws (rad/sec)?MotorGear4 in MajorDiameterPower Screws70 TonSluice GateHe = 0.24v 3 ft/minAns.P = 59.37 hpW₁ = 5.655 rad/s

Given:f = 0.1fc = 0.24v = 3ft/min = 36 in /minTo find:Power required to drive each screw when the…

Answered: Two identical 4 in. major-diameter…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A flange coupling is to connect two 57mm shafts. The hubs of the coupling are each 111m indiameter and 92mm hub length. Six 16- mm bolts in a 165-mm diameter bolt circle connects theflanges. The key is 14mm high, 14mm wide and 86mm long. Coupling is to transmit 45kW at 160 rpm.For all parts, yield point value in shear is one-half the yield point value in tension or compression thatis 448MPa. Determinea. Shearing stress of the key and its factor of safetyb. Bearing stress of the key and its factor of safetyc. Shearing stress in bolts and the factor of safety based on yield point
Question 4 Squared & ground end A multi disc clutch, as illustrated below, is used to connect a four-cylinder internal combustion engine to a roll mill. The lining material is made of cast iron (Permissible pressure 1.725 MN/m) and friction coefficient of 0.06 running in oil. If the outer diameter of the plates is limited to 200mm and the inner diameter to 100mm, compare the maximum amount of power that can be transferred at 2500 rpm by using the a) principle of uniform pressure and b) uniform rate of wear. (16)
You have to build a box lifter, this will be made with a square threaded power screw. The power screw is 3 inches in diameter and 2 threads per inch. To improve the speed of raising and lowering the boxes, it must be with triple thread. The coefficient of friction of the screw and collar is 0.25, the diameter of the collar is 4 inches.Calculate:1. The depth of the thread, the width of the face, the average diameter, the root diameter, the pitch and its feed.2. The torque to increase the load and the efficiency of the screw.3. The speed of the motor (in rpm), if it is directly coupled to the screw and it is desired that the boxes rise at a speed of 30 inches/min.
You have to build a box lifter, this will be made with a square threaded power screw. The power screw is 3 inches in diameter and 2 threads per inch. To improve the speed of raising and lowering the boxes, it must be with triple thread. The coefficient of friction of the screw and collar is 0.25, the diameter of the collar is 4 inches.Calculate:1. The depth of the thread, the width of the face, the average diameter, the root diameter, the pitch and its feed.
The effective pressure on a 400 mm diameter piston is 1.1 MN/m² when the crank is 32° beyond top dead centre. The stroke of the engine is 900 mm, the connecting rod is 1500 mm in length and the coefficient of friction for the lubricated crosshead guide is 0.025. Calculate EACH of the following: (a) the magnitude of the instantaneous torque; (b) the magnitude of the instantaneous force to overcome guide friction.
A single-threaded power screw with square threads lowers a load of 3,856 N at a speed of 43 mm/s. The screw has a mean thread diameter of 16 mm and a pitch of 3 mm. The frictional coefficient of the threads is 0.32, and collar friction is negligible. How much torque must be applied to drive the screw with the applied load in units of newton meters? The efficiency of a
An overhang shaft carry a 900mm diameter pulley, whose center is 250mm from the center of nearest bearing. The weight of the pulley is 600N and the angle of lap is 180°.The pulley is driven by motor horizontally to right it, if the permissible tension in the belt is 2650N and the coefficient of friction between the belt and the pulley surface is 0.3, estimate the diameter of the shaft. Note, Neglect centrifugal tension and assume permissible tensile and shear stresses in the shaft as 84MPA and 68MPa respectively.
Question No. 11: In a thrust bearing the external and internal radii of the contact surfaces are 210 mm and 160 mm respectively. The total axial load is 60 kN and coefficient of friction = 0.05. The shaft is rotating at 380 rpm. Intensity of pressure -is not to exceed 350 kN/m2. Calculate: Power lost in over-coming the friction and; Number of collars required for the thrust bearing.
A square thread power screw has pitch of 4-mm with double threads. Applicable data are threadand collar coefficient of friction equal to 0.08, collar diameter of 40-mm, and a load of 6.4-kNper screw and mean diameter of 30mmDetermine:a. Torques required to rotate the screw with” and “against” the load.b. Overall efficiency.
A flange coupling is to connect two 57 mm shafts. The hubs of the coupling are each 111 mm in diameter and 92mm thick and the flange web are 19 mm thick. Six 16 mm bolts in a 165 mm diameter circle connect the flange.The keyway is 6 mm shorter than the hub’s thickness and key is 14 mm x 14 mm. Coupling is to transmit 45 KW at160 rpm. For all parts, yield point value in shear is one – half the yield value which is 448 MPa. Calculate the forceon the shaft
A double threaded Acme screw of 1.5-in major diameter is used in a jack to raise a 6.5 kip load. The jack has a plain thrust collar with 2.2-in mean diameter and the coefficients of kinetic friction are estimated as 0.12 for the collar and 0.15 for the screw. If the screw has the following parameters. lead 0.5 in, thread angle in the normal plane - 14.4, and mean diameter 1.375 in, determine the running efficiency of the jack in raising the load N] 35
An acme thread power screw that has a mean diameter of 25 mm and pitch of 5 mm is used to lift a load of 500 kg. If friction on threads is 0.1, determine the torque needed to turn the screw.

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS