Two blocks of wood, 50 mm wide and 20 mm thick, are glued together as shown in figure below. Using the free body diagram concept illustrated in Fig. below, 1. Show that the shearing stress on a plane inclined at any angle to a transverse section of area A is T=Psin20/2A? Given: sin 20 = 2 sin cos 0. 2. Determine the shear stress, if the axial load P=6000 N.? Funu ost A.

Two blocks of wood, 50 mm wide and 20 mm thick, are glued together as shown in figure below. Using the free body diagram concept illustrated in Fig. below, 1. Show that the shearing stress on a plane inclined at any angle to a transverse section of area A is T=Psin20/2A? Given: sin 20 = 2 sin cos 0. 2. Determine the shear stress, if the axial load P=6000 N.? Funu ost A.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

SITUATION 2: Find the smallest diameter of bolt and the minimum thickness of each yoke that can be used in the clevis shown in the figure below if P = 400 KN. The shearing strength of the bolt is 300 MPa and the bearing strength is 500 MPa. € Yoke
Question 1 double-shear pin connections at Band D. All pins are 7 mm in diameter. a = 750 mm, b = 350 mm, h= 550 mm, P= 725 N, and 8 = 55° Determine the shear stress in pin B. Answer in MPa rounded-off to 2 decimal places. (1) a b P
In the figure, two planks are fastened together with a sheet plate with a thickness of 4 mm. Since 1 kN load is applied to the plank; a) The maximum normal stress occurring in the plate, b) Find the shear stress on the M10 bolt and the bearing stress on the plate (the thread bottom diameter of the M10 bolt is approximately 8 mm)
STRENGTH OF MATERIALS (NO LONG EXPLANTION NEEDED. RATE WILL BE GIVEN) Two blocks of wood, 50 mm wide and 20 mm thick are glued together as shown. If P is 600N, the shearing stress in the glued joint is
Q.3. For figure Q3, find rivet diameter, where t = 100MPa ? 20mm O O 30mm 1909 20mm- 30mm Fig.Q.3 4 KN 25 550mm-
Q.5) A bar of 1000 mm length and 40 mm diameter is centrally bored for 300 mm length at one end at a diameter of 20 mm. Young's modulus of the material is 2 x 10° N/mm². If the bar is 2 40 mm 20 mm 700 mm 300 mm loaded axially with a load of 30 kN the extension produced is (A) 0.1136 mm (C) 0.1478 mm (B) 0.1313 mm (D) 0.1542 mm
please do it fast and clearly and don't copy from others otherwise skip please thanks
Solve following the problems below and show your complete, systematic and neat solution. Upload your solution with one PDF file. 1. For the beam shown, a. determine the maximum flexural stresses in compression ant tension. b. determine the flexural stress of the fiber located at 3m from the left support and 50 mm above the bottom 18 kN/m 300 mm 6 kN/m 20 mm 27 kNm 22 2m 2m 3 m +m 15 mm - - 50 mm 360 mm 20 mm
A steel truss structure is loaded as shown in Fig. 1. The truss members are made of A36 steel (f, = 36 ksi). All the members are made up of two 3.0"x5.0" (each) parallel flat bars. All the joints have bolt connection (pin connection), acting in double shear. The diameter of all the bolts is 3.0". Determine, •The average normal and shear stresses in bars AB, and Cl and the shear stress in pin H. •The average normal and shear strain in AB, and CI and shear strain in pin H (Given, E = 29x106 psi, G = 11x 106 psi) 4k 4k C IH or GH 8 ft A Pin H JT H 4k 6 @ 8 ft = 48 ft Fig. 1
B. See figures attached for reference and solve carefully/ellaborately, include the units and draw the diagram. Your works will be appreciated much, Thanks! A rectangular steel bar 0.5 inch thickness by 1.5 inches width and 220 ft long is subjected to a 6000 lbs tensile load acting along its width. Find the deformation along its length and thickness if poison’s ratio is 0.27