Twelve liters per minute of hot water at 330 K flow through a 0.5 inch schedule 40 (0.622 in wall thickness) domestic hot water line. What is the heat transfer coefficient inside the pipe? The kinematic viscosity is 0.5 x 106. The Prandtl number is 3.2.

Twelve liters per minute of hot water at 330 K flow through a 0.5 inch schedule 40 (0.622 in wall thickness) domestic hot water line. What is the heat transfer coefficient inside the pipe? The kinematic viscosity is 0.5 x 106. The Prandtl number is 3.2.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter6: Forced Convection Over Exterior Surfaces

Section: Chapter Questions

Problem 6.19P

See similar textbooks

Similar questions

Evaluate the Reynolds number for flow over a tube from the following data: D=6cm,U=1.0m/s, =300kg/m3,=0.04Ns/m2.
Water going into a pipe with a tempeture of T1 and going out T2 . ambient tempeture is T0. flow rate q. Develop an expression for T2 ( based on heat transfer) Length of the pipe Lh0 - convective heat transfer coefficient of the airhW -convective heat transfer coefficient of the waterk- pipe thermal conductivity (W/m·K)d – pipe diameter Use any other varilable that you need and can be found online easily .
Q2:A) Define the bulk temperature (Tn), and prove that : T₁, - 2 ur dr B) Ethylene glycol flows at 0.01 kg/s through a 3 mm diameter, thin walled_tube. The tube is coiled and submerged in a well-stirred water bath maintained at 25 °C. If the fluid enters the tube at 85 °C, what heat rate and tube length are required for the fluid to leave at 35 °C ? At 60 °C, μ = 0.00522 kg/m.s, k = 0.26 W/m.K, C, 2562 J/kg.K. -
2. Engine oil (similar to oil C) flows at 1.2 ft/s through a 1-inch diameter tube. The bulk oil temperature is 190 F and the tube surface temperature is 210 F. Determine the unit convective coefficient for a tube length of 10 ft. If the tube length is doubled, what is the percentage increase (or decrease) in the film coefficient? Let k = 0.96 Btu-in/hr-ft2-F and c = 0.52 Btu/lb-F for the oil. *
Select the letter of the correct statement. Write the answer with calculations, drawing, rules or explanation 2-) A scientist suggests the following correlation be used for square tubes in a liquid cross-flow situation (Nu = 0.102 Re0.675 Ppl/3). Water (k = 0.61 W/m.K, Pr= 6) flows across a 1-cmsquare tube with a Reynolds number of 10,000. The convection heat transfer coefficient is:(A-) 5.7 kW/m?.K(B-) 8.3 kW/m?.K(C- ) 11.2 kW/m?.K(D-) 18.1 kW/m?.K.
QUESTION 9 A liquid cooled heat sink for a smartphone is sketched in Figure Q9. It uses water of density p = 997 kg m-3 and kinematic viscosity v = 1.19 x 10-6 m²-s-1 that runs in the x₁ direction through each of the five tubes of constant diameter D₁ = 5 mm and length Lx1 = 20 mm. It is supplied by a U = 0.017 m-s-1 uniform water inflow. Use Blasius' skin friction coefficient Cf = 0.664 / Rex1 0.5 to calculate the total skin friction drag force imparted by the flow on the heat sink walls. Calculate your answer in microNewtons, to one decimal place and enter the numerical value only. 1 microNewton = 10-6 Newtons. Partial credit is awarded for a reasonable approximation to the correct numerical answer. Lx₂ X2 Lx1 X1 Ő ve Heat Flux (9) (a) Figure Q9: Schematic of a liquid cooled heat sink LX3 4
2, The internal diameter of a boiler generating tute is 4in. and the wall thickness is 0.375 in. In operation the external surrace film temperature is 26 Btu/hr . ft².°F, the internal film coefficient is 1700 Btu/hr.ft².°F and a 0.375 in. thickness scale having a conductivity of 0.6 Btu/hr.ft. °F is deposited on the inner surface of the tube. The metal conductivity is 26 Btu/hr.ft. °F, the furnace gas temperature is 2100 °F and the temperature of the water is 500 °F, calculate (a) the overall coefficient of heat transfer for the clean tube, (b) the overall heat transfer coefficient including the effect of the scale, (c) the external tube surface temperature before and after the scale
Water going into a pipe with a tempeture of T1 and going out T2 . ambient tempeture is T0. Develop an expression for T2 ( based on heat transfer) Length of the pipe Lh0 - convective heat transfer coefficient of the airhW -convective heat transfer coefficient of the waterk- pipe thermal conductivity (W/m·K)d – pipe diameter Use any other varilable that you need and can be found online easily .
48. Water is flowing in a smooth pipe of diameter D. A section of this pipe hav- ing a length of L is heated. Water at the inlet to the heated section has a tempera- ture of Tŋ. Water temperature at the exit of the heated section is Tp. The heated section of the pipe wall is maintained at a constant heat flux so that a constant temperature difference of AT, = T, – T, exists between the wall and the bulk wa- ter temperature. Show that for turbulent flow in the pipe and a specified heated length and pipe diameter, water temperature at the exit of the heated section is given by: 402 0.6 Pr T52 =Tf +0.0876 L AT DO.8 0.2 m
long. The inlet water temperature is 10 C, and the tube wall temperature is 15 C water temperature. k 0.585, Pr= 9.4, u= 1.31x10*,p= 992kg/m, CP= 4195 j/kg. higher than the water temperature all along the length of the tube. What is the exit %3D Q5//answer one of the following branches e jall al je yal A) cast iron pipe (k=75w/m. °C) air flows inside this pipe at 300°C the inner diameter is 0.06 m, the outer diameter 7cm,it is covered with insulation type glass wool with thick 4cm. with k= 0.055w/m.°C .the ambient temperature 6 °C by free V3. convection with heat transfer coefficient (20w/m2. °C) the heat transfer inside the pipe is 65 w/m?. °C. length of tube (L-2) determine 1-the heat lost from the hot air 2-the temperature drop across the pipe shell 3-the temperature drop across the insulation. 344 14. 1256 and B) Fill the blanks: of the 1. The thermal resistance of a medium depends on medium. 2 All law. pes of convection are governed by 10000, the flow is
the tube length is 1m.
THEORY AND PRIMCIPLE OF PIPE INSULATION