Traverse Surveying Given the survey data below with the northing and easting of A being 15000.00 and 20000.00 respectively, solve the following problems: COURSE DIST, L (m) BEARING AZIMS AB 475.48 N 00°50'E 180°50' BC 649.13 N 63°54' W 116°06' CD 867.34 S 25°54' W 25°54' DE 522.48 S 44°40'E 315°20' EF 504.90 N 33°27' E 213°27' FA 311.25 S 84°21' E 275°39' SUMS 3330.58 1. Balance the traverse using Compass rule, determine the corresponding REC and the coordinate of points. 2. Balance the traverse using Transit rule, determine the corresponding REC and the coordinate of points. 3. Compute the area by coordinates using the results of the compass rule adjustment. 4. Compute the area by DMD and DPD using the results of the compass rule adjustment. 5. Divide the adjusted traverse into two equal tracts by a dividing line passing thru A using the results of the compass rule adjustment.

Traverse Surveying Given the survey data below with the northing and easting of A being 15000.00 and 20000.00 respectively, solve the following problems: COURSE DIST, L (m) BEARING AZIMS AB 475.48 N 00°50'E 180°50' BC 649.13 N 63°54' W 116°06' CD 867.34 S 25°54' W 25°54' DE 522.48 S 44°40'E 315°20' EF 504.90 N 33°27' E 213°27' FA 311.25 S 84°21' E 275°39' SUMS 3330.58 1. Balance the traverse using Compass rule, determine the corresponding REC and the coordinate of points. 2. Balance the traverse using Transit rule, determine the corresponding REC and the coordinate of points. 3. Compute the area by coordinates using the results of the compass rule adjustment. 4. Compute the area by DMD and DPD using the results of the compass rule adjustment. 5. Divide the adjusted traverse into two equal tracts by a dividing line passing thru A using the results of the compass rule adjustment.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: What are some of the advantages and disadvantages of using an internal static analysis,

A: Static code analysis is a method of debugging that involves inspecting source code before running a…

Q: Design an irrigation channel with the following data: Full supply discharge = 6 cumeci Rugosity…

A: Given data Q = 6 m3/sec n = 0.0225 m = 1 S = 1 in 5000

Q: A horizontal beam 16 ft long is subjected to a load of 500 lb located to its center. The dimension…

A: Given: Beam with point load at center Beam dimensions To find: Flexural stress Notations; M =…

Q: difference between the stress distribution of these two- equations ab a distance r= 0.02 a ahead of…

Q: Write an official letter to the authorities responsible for the provision and service of water…

A: Brief concept introduction- water supply- Water supply in any region is a very very crucial aspect…

Q: The center panel of the truss contains two flexible cables. What load P will cause a compressive…

Q: 1. A backsight of 3.055 m is taken on a point 75 m from a level station and a foresight of 1.258 m…

Q: OCC A B C D DISTANCE (m) ? 150.932 ? 209.613 E F 134.912 F A 110.147 Sketch the data above and solve…

A: first convert the bearing in WCB

Q: a concentrated load P is acting at the center of the beam having a simple span of 9m. the beam is…

Q: The system is released from rest with the spring initially stretched 3 in. Calculate the velocity v…

Q: Problem 1.01 A simply supported beam sustains a total dead load of 24 kN/m and live load of 35 kN/m…

A: Given : Dead Load = 24 kN/m, Live Load = 35 kN/m Span, L = 6 m, B = 350 mm, d = 550 mm, D = 620 mm…

Q: 10 m +6m + 6 m Q: If the flow discharge of a trocar (trapezoid) is shown in the figure below (80…

Q: 1.5m= D ↓ 20 kN/m² 71-18 kN/m² 41-30 ₁=0 (2) 0.5m → 4 0.7m (3) * C -0.7 m-0.7 m 2.6 m O P, H₂=6 m P.…

Q: C E = constant sol/m B 48. Tin 27 E 1m ㅈㅈ I -75kw *

A: S.I = 3m + R -3j S.I = 3(3) + 4 - 3(4) =1 Choose Redundant force P as a horizontal reaction at A and…

Q: What will be the value of reduction factor R, if value of At is given to be 500ft²?

A: Given data- Area At=500 ft2since1 ft2=0.092903 m2⇒At=500 ft2=46.415 m2

Q: A farm water trough of length 5 m and width 4 m is supported on four timber beams of Douglas Fir.…

A: "Since you have posted a question with multiple sub-parts, we will solve first three sub-parts for…

Q: y A P 2 ft 63 B 6 ft с -4 ft →→→→ D ·X

A: Draw the shear-force and bending-moment diagrams for the beam shown. Determine the shear force 10.7…

Q: At a section in the triangular channel the average velocity is 8 ft/s. Determine (a) the critical…

Q: Q2: 1- A centrifugal pump is to be operated with discharge 2.5 m3/min. If the power needed for the…

A: Compute the total head of the pump,H=?

Q: For the beam shown, calculate the magnitude of the bending stress (in psi) at a point 1.14 in from…

Q: 6. Solve the below structure with displacement method, and plot out its M diagram. EI= constant.…

Q: A rectangular footing has dimensions shown and is acted upon by a dead load of 1200 kN and a live…

A: Answer We are given Dead Load = 1200 KN Live load = 1600 KN Thickness of footing = 500 mm f'c = 28…

Q: C B 30 400mm 600mm TALN 6kN a) Calculate the force, FAB at point AB.

Q: Design an irrigation channel with the following data: Full supply discharge = 10 cumec Bazin's…

Q: Example: Copper Material Distance between anchor= 100 mm L = Im h = 6.5mm, b = 25.5 mm I…

A: Given data: Distance between the anchor = 0.1 m L= 1m h=6.5 mm b= 25.5 mm I=583.6 mm4. Y=3.25 mm

Q: 3. A moist soil has total volume of 0.00708 m³, total mass of 13.95kg and moisture content of 9.8%…

Q: (5,0,-2) and b=(4,-7, 10) the projection a on b to is.

Q: A wide, clean-earth river has a flow rate q = 150 ft³/s per foot. (a) What is the critical depth, Yc…

Q: y 21 4 2 X

Q: The 2-lb collar is released from rest at A and slides freely up the inclined rod, striking the stop…

A: Apply conservation of energy at A and B. The velocity at B can be evaluated.

Q: Example 3: Design a trapezoidal channel of water having a velocity 0.6 m/s, channel side slope…

Q: 19. Two circular primary clarifiers are to be installed in a sewage treatment plant processing the…

A: NOTE- Hi! Thank you for the question, As per the honor code, we are allowed to answer three…

Q: An EDM slope distance AB is determined to be 561.276 m. The EDM instrument is 1.820 m above station…

Q: 03: Fill in the blanks in the following: 1. If a=(3,-2, 6) and b=(4,-1,-6) the axb = ********

Q: A turbine developing 15000 hp and it turns the shaft at 300 rpm. The propeller which is attached the…

Q: Design the necessary shear reinforcement (if needed) in the form of U-stir sectionshown in Fig.5.22.…

Q: A pipe has a uniform diameter of 750 mm. The flow rate entering the pipe is 3.92 m^3/s. The exit…

Q: Q: If the flow disc a trocar (trapez shown in the figu (80 m/s), what amount of flow di if the level…

Q: ed sludge system treats wastewater from an industry with a flow rate of 10 y. The BOD of the raw…

Q: 10 ft t COMPUTE FOR THE MAXIMUM MOMENT. UNIT: lb.in 800 lb/ft

Q: What is the expected head loss per 1 mile in feet of a closed circular pipe (17 inches inside…

A: Given data in question Diameter Discharge Friction factor To find out Head loss

Q: 2 w A * EI=20000 KN. m² 2/ Find thiforme 3m 2m 4 Load() if the deflection at Dis (3mm) 4pward ? B F…

A: Given : Overhang beam with UDL Double integration method E = 20000 kNm2

Q: Q.4. Compute the design shear strength of the beam cross section shown in the below figure with the…

Q: rise of v the heigh

Q: SOLVE THE INDETERMINATE STRUCTURE USING CASTIGLIANO’S THEOREM AND SHOW COMPLETE SOLUTIONS.…

A: Given A symmetrical indeterminate structure Required Moment at B and C using Castigliano's method…

Q: Plot the shear force and bending moment diagrams for each element. A BK- D 12m тву 6m bm

Q: Draw an activity diagram for the following scenario: Passenger who needs to purchase a travel ticket…

A: Based on the given data we can list down the activity and then represent with activity diagram 1)…

Q: irrigation water (in mm) required for irrigating the crop is

A: The values given in the question are as follows: Permanent wilting point(ϕ)=18% or 0.18 Field…

Q: The cross section of a pin-ended column varies as in Fig. 2. Determine the critical load using TX n…

Q: Find the margin of error for the 95% confidence interval used to estimate the population proportion.…

A: Following are required answers :

Concept explainers

Electric Circuit and Components

An electrical circuit or electrical network is a pre-determined pathway to make the electrons flow in the desired direction. The flow of electrons will set up a current flow in the circuit. Normally, the flow of electrical current is opposite to the flow of electrons. An electron is a fundamental sub-atomic particle of an atom possessing a negative charge. To initiate the flow of current and achieve the desired output, the electrical circuit should necessarily be composed of closed pathways. The pathways are made-up of good conductors of electricity such as aluminium and copper.

Question

thankyou for helping out! have a nice day :)) godbless

Traverse Surveying
Given the survey data below with the northing and easting of A being 15000.00 and 20000.00
respectively, solve the following problems:
COURSE
DIST, L
(m)
BEARING
AZIMS
AB
475.48
N 00°50'E
180°50'
BC
649.13
N 63°54' W
116°06'
CD
867.34
S 25°54' W
25°54'
DE
522.48
S 44°40'E
315°20'
EF
504.90
N 33°27' E
213°27'
FA
311.25
S 84°21' E
275°39'
SUMS
3330.58
1. Balance the traverse using Compass rule, determine the corresponding REC and the coordinate of
points.
2. Balance the traverse using Transit rule, determine the corresponding REC and the coordinate of
points.
3. Compute the area by coordinates using the results of the compass rule adjustment.
4. Compute the area by DMD and DPD using the results of the compass rule adjustment.
5. Divide the adjusted traverse into two equal tracts by a dividing line passing thru A using the results
of the compass rule adjustment.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step 6

Step 7

Step 8

Step 9

Trending now

This is a popular solution!

Step by step

Solved in 9 steps with 9 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

S LINEAR ERROR OF CLOSURE N Problem 2: W E U For the given data of a transit-tape survey. S 1. Determine the latitudes and departures of the lines. 2. Determine the linear error of closure. 3. Determine the bearing of the line of the side error. V 4. Determine the relative precision. LINE LENGTH (m) BEARING LATITUDE DEPARTURE +N -S +E -W Y AB 495.85 N 05°30'E BC 850.62 N 46°02'E CD 855.45 S 67°38'E DE 1020.87 S 12°25'E EF 1117.26 S 83°44'W FA 660.08 N 55°09'W Total ΣNL ΣSL ΣED EWD 3 RVE
Q3): The following data were collected while running a closed traverse ABCDA starting from A toward B. Calculate: 5- Linear misclosure 6- Traverse precision Line Length (m) Azimuth AB 181°25' BC CD DA 330 767 411 727.438 89' 50 355 263° 32' 17" Point A (fixed) B C D A (calculated) Easting (m) 337.499 392.341 1159.34 1123.518 N Northing (m) 600.500 270.601 272.832 682.268 D Angles B = 88° 25' C = 85° 10'
Q3): The following data were collected while running a closed traverse ABCDA. Calculate: 1- Coordinates of B (Easting and Northing). N 2- Linear misclosure Line AB BC CD DA 3- Traverse precision 4- Interior angles A and B 5- Distance BC and CD. 6- Coordinates of C (Easting and Northing). Length(m) 330 827 Sum= 2435.15 Azimuth 181°25' 89°50' 355°00' 264°18'20" Point A B C D A (calculated) Easting 500 B 1323.167 Northing 500 582.059 A= B= Angles
Q3): The following data were collected while running a closed traverse ABCDA. Calculate: 1- Coordinates of B (Easting and Northing). N Line AB BC CD DA 4- Interior angles A and B 5- Distance BC and CD. Length (m) 330 827 Sum= 2435.15 Azimuth 181°25' 89°50' 355°00' 264°18'20" Point A B C D A (calculated) = Easting 500 B 1323.167 Northing 500 582.059 A= B= Angles
Using the previous exomple, bolance the departures and latitudes using the transit rule. Correer DEP (DEP of course) Corrur"ELAT (LAT of course) OEVALUATE Compute the area of the given traverse using DPD and DMD method. COURSE LENGTH (m) BEARING AB 495.85 NOS" 30' E BC 850.62 N 46° 02' E CD 855.45 S 67* 38 E DE 1020.87 S 12* 25 E EF 1117.26 S 83* 44' W FA 660.08 N 55" 09' W ERSITY
Q3): The following data were collected while running a closed traverse ABCDA. Calculate: 1- Coordinates of B (Easting and Northing). N Line AB BC CD DA 4- 5- Distance BC and CD. 6- Coordinates of C (Easting and Northing). Interior angles A and B Length(m) 330 827 Sum= 2435.15 Azimuth 181°25' 89°50' 355°00' 264°18'20" Point A B C D A (calculated) = Easting 500 B 1323.167 Northing 500 582.059 A= B= Angles
2. Given in the table below is the technical descriptions of a transit-tape survey of a closed traverse. Determine the distances of lines Ab and DE. LINES BEARINGS DISTANCES S 560 30' AB E S 100 00' BC 650.00 m N 880 30' CD W 1100.00 m N 020 10' DE W N 570 20' EA 640.00 m
Two angles BAC and CAD and a single angle BAD are measured at the same point A. Determine the most probable value for each angle. ANGLE Observed value No. of measurement ВАС 28°24'00" 1. CAD 61°15'00" 3 BAD 89°24'00"
Correct the survey data below for a closed traverse. LINE DISTANCE BEARING AB 495.85 m N 05°30’ E BC 850.62 m N 46°02’ E CD 855.45 m S 67°38’ E DE 1,020.87 m S 12°25’ E EF 1,117.26 m S 83°44’ W FA 660.08 m N 55°09’ W
A closed-loop traverse ABCDA was run around an area and the following observations were made: Length Included angle Station W.C.B. at to (m) A 187.4 86°30'02"| 140°11'40" B B 382.7 80°59'34"| C C 106.1 91°31'29" D D 364.8 100°59'15" A Adjust the angular error, if any, and calculate the coordinates of other stations if the coordinates of the station A are E1000 m and N1000 m.
The following are the observed data for an open compass traverse. Adjust the observed directions and tabulate values accordingly. LINE LENGTH OBSERVED BEARING FORWARD BACKWARD AB BC CD DE EF FG 462.50 m 405.65 m 495.08 m 284.15 m 367.29 m 217.73 m S 40o25’ W S 55o40’ W N 36o15’ W N 73o10’ W S 44o45’ W S 20o30’ E N 40o30’ E N 55o50’ E S 35o55’ E S 73o30’ E N 44o45’ E N 21o00’ W
SITUATION A closed traverse has the following data: LINE DISTANCE BEARING N 47° E S 69° E S 39° W S 87° W N 25° W АВ 179.00 258.20 BC CD DE EA ? 145.41 2 What is the length of line CD? 3 What is the length of line DE?