To points A, B, C, and D respectively on an infinite-length plate Parallel forces FA, FB, FC and FD (kN) act in the directions given in the figure. Point A is blue, point B is white, point C is yellow, point D is on the green area. Find the magnitude of the equivalent resultant force and the x and y (m) coordinates of the application point by using the values specific to your name in the data table. FAl A(XAYA,O) FD D(Xp.Yo.O) y Fl B(XB,YB,0) C(XcYcO),

To points A, B, C, and D respectively on an infinite-length plate Parallel forces FA, FB, FC and FD (kN) act in the directions given in the figure. Point A is blue, point B is white, point C is yellow, point D is on the green area. Find the magnitude of the equivalent resultant force and the x and y (m) coordinates of the application point by using the values specific to your name in the data table. FAl A(XAYA,O) FD D(Xp.Yo.O) y Fl B(XB,YB,0) C(XcYcO),

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A machine component is subjected to the forces and couples shown. The component is to be held in place by a single bolt that can resist a force but not a couple. Determine the distance of the bolt hole from point G if it is to be located on line FG. 125 N 15° 200 N E 50 mm 42 N-m 520 mm 240 mm 50 mm D 70° 40 N-m 640 mm H C 80 N 20 N 180 mm B 50 mm
answer for Vd, Mf, and Mc
Q4- Find the following integrals: 1- sin³ x cos x dx x²+1 2- S dx (x-1)³
Follow my table sokve correct SOLUTIONs
How many minutes you took Name: to solve this problem? ID.: Section : HW-2 Replace the loading by an equivalent resultant force and determine where its line of action intersects post AB measured from B. 0.5 m B. 500 N 1m 02 m 250 N 30 1m 300 N
Plate # 4 A W24x103 is used as a beam that is simply supported. IT has the following Properties d= 623.10mm tw = 14.00mm bf = 228.60mm tf = 24.90mm A = 19548.00mm^2 w = 153.76kg/m rt = 59.18mm Ix = 1,248,694,000,000mm^4 Sx = 4,008,005mm^3 rx = 252.74mm Zx = 4,588,377.92mm^3 ly = 49,532,000,000mm^4 Sy = 433,350.83mm^3 Ry = 50.34mm Fy = 248MPA Determine the allowable (ASD) Moment Capacity in kNm for a length of: a) 2m b) 4m c) 9m d) 16m
-6 -3 -5 9 -7 9. J= 2 1 -5 4 -7 9 5 7 -7 0 a3 a3 0 а b b2 b3 b4 10. K %3D c3 0 C d² 0 d2 d³ 0
Questions T 40 mm TABLE 3.1. Coefficients for Rectangular Bars in Torsion a/b C₁ C₂ 1.0 0.208 0.1406 1.2 0.219 0.1661 60 mm 1.5 0.231 0.1958 2.0 0.246 0.229 2.5 0.258 0.249 3.0 0.267 0.263 4.0 0.282 0.281 5.0 0.291 0.291 N 10.0 0.312 0.312 0.333 0.333 1. Determine the largest torque T which may be applied to end of the solid bar which is shown in the diagram above, knowing that the maximum allowable shear stress = 107 MPa and G = 40 GPa. Provide the answer in kNm with precision to two decimal points. 2. The same solid bar is subjected to a torque of 1.5 kNm. Its total length, denoted as z, is 601 mm. What will be the angle of twist? Provide the answer in degrees with precision to two decimal points.
Problem- In a pressure penstock 4500 m long, water is flowing at a velocity of 4 m/s. If the velocity of the pressure wave travelling in the pipe, due to sudden complete closure of a valve at the downstream end, is given as 1500 m/s. What will be the period of oscillation under frictionless conditions.
A steel bar shown is made up of two segments. Determine the displacement of A relative to fixed support D.
d?y dy 7y = 6e2x, dx2
Problem 106 dy If, for t> 0, x=1° and y = cosr, then dx a. cost c. - sin 2t b. -sin1? d. - cos 2t