Time taken for the output signal  rise to 95%  from 10% is called rise time Select one: True False

Q: The Companding occurs only when; O a. Small and large signals are attenuated O b. Small and large…

A: Note : The correct option D. Small signal amplifier and large signal attenuated. With companded PCM…

Q: an input signal ranges from 20–40 A (microamps), with an output signal ranging from .5–1.5 mA…

A:

Q: frequency modulation and what is the highest value for

A:

Q: 13. The purpose of the __________ is to periodically sample the continually changing analog signal…

A: 1) The purpose of the quantisation is to periodically sample the continually changing analog signal…

Q: c. Draw the small-signal equivalent circuit for the amplifier. lout lin ig id Cgs 9mVgs RD Rext Vout…

A:

Q: assuma VA=15, perform large signal model and small sginal analysis, drow the equivelnt small signal…

A:

Q: Q4: Draw the constellation diagram of 2*4 QAM signal then show the output amplitudes and phases of…

A:

Q: The output from a sensor ranges from a minimum of 10 mV to a maximum of 200 mV as the measurand…

A: An instrumentation amplifier allows an engineer to adjust the gain of an amplifier circuit without…

Q: ..... .. .. ... .... ... In PCM, the first step after PAM, is coding of the analog pulses. Select…

A: We need to tell about the PCM .

Q: b) Determine the input waveforms 4 and that pridaced the output waveforms in Figure bellow. NAND…

A:

Q: the input frequency iš I MHZ. If the coûntér iš át štátě 6, whát will bè thẻ count after 60 pulses.

A:

Q: What is the name of the signal which is indicated by the red line? E) Costreller Y6) 2- NG) O A)…

A: for any control system there are inputs, outputs and error signals . inputs are the signals which…

Q: Q1) Determine Ic,VCE, Icisat) and VCE(cut off). Also, construct DC load line and plot Q-point.…

A:

Q: In a Schmitt-trigger circuit, the output is a digital signal that stays at a high voltage level when…

A: We’ll answer the first question since the exact one wasn’t specified. Please submit a new question…

Q: Define moore state machine. Draw Mealy state diagram of sequnce 1111 with overlapping condition.

A: The state diagram is visual representation of the sequence. It shows the internal states and…

Q: The most common technique to caneg analog to digital data is called Pulse Code Modulation(PCM). What…

A: The most common technique to caneg analog to digital data is called Pulse Code Modulation(PCM).…

Q: Needs Complete solution with 100 % accuracy don't use chat gpt or ai plz plz plz.

A: Here's a breakdown of how it works:Components:BJT (Q1): This is likely an NPN BJT transistor,…

Q: 6. Draw the circuit diagram and find the value of 'X' bit for a digital to analog conver, if Vout…

A: According to the question we have to draw the circuit diagram and find the value of 'X' bit for a…

Q: Signal-to-Noise ratio is calculated as: Select the correct response: A. signal voltage divided by…

A:

Q: (2) Consider a frequency modulated signal. The modulating signal frequency is increased from 10 kHz…

A: In this question we have to find the correct optionsrgarding modulated signal bandwidth

Q: n . when input change, may affect the output Morre model Mealy model O

A:

Q: For each of the 8 circuits below, draw small signal model and calculate Vout/Vin. Vb1, Vb2 are dc…

A:

Q: What is the problem with AM signal when overmodulation occurs?

A: When AM signal is overmodulated,

Q: second modulating tone having the same amplitude but a different frequency is added to the first at…

A: We need to find out modulation index

Q: Find the resonance point and the half-width of the speed versus frequency curve for the damped…

A: When b / m << 2ω0 (half width of speed), we say that the oscillator is lightly damped. For a…

Q: about nyquist stability criterion in deatials

A: Need to find about nyquist stability criteria

Q: Q. ) What are the frequencies F1, F2, F3 10MHZ is applied? after each stage if an input clock of…

A: Counter is a  sequential circuit made up of flip flop which are connected to count the pulses . It…

Q: The error detector compares the ....to the and .. .. produces an error signal equal to the…

A: In this question we need to choose a correct option.

Q: A chopper has input voltage of 270 and the load resistance as 7N, the average load current as 53A.…

A:

Q: Rout Ve

A:

Q: can you help me at least up to paragraph 3 or 4, please?

A: The objective of the question is to design a decadic counter that operates in up/down mode using…

Q: Qz a)_ (alcelate fregeuency that will make the eutput wohtnge VocE) fiqure Q2 w "be eqpal to the…

A: Calculate the frequency , the output voltage Vo is be equal to the input voltage Vi

Q: 1. What is the condition for over modulation and what are its effects?

A:

Q: 1)to VRMs value to generate a signal with a peak voltage of 10 V with a signal generator in a…

A: Given :    In the question they have mentioned the maximum value of the alternating voltage and they…

Q: 1. Small scale fading describes the fluctuations of the amplitude, phases of a signal.

A: The solution is provided in the following section.

Q: [0 5] the signal in the volt range will be quantified. since n=4; a)Calculate what is the number of…

A: We need to calculate number of level , and step size for quantization .

Q: The shown sampled signal is the output of the ADC of Arduino Uno, calculate: 1- The number of…

A: Understanding the CircuitIdentify the Components:Look for common digital logic components like AND…

Q: The attenuation in the pass band or stop band is called a. Cutoff Frequency b. Ripple c. Band…

A:

Q: Assuming that a certain ASM chart has 5 states, the size of each multiplexer required to implement…

A: for a ASM  states=52no. of flips=statesno. of flip flops =3MUX reqires = 3

Analog to Digital Converters

The analog-to-digital converter (ADC) allows circuits controlled by microprocessors, Arduinos, Raspberry Pi, and various reasonable digital circuits to be connected to the real world. In the real world, analog signals have a continuous stream of information from a variety of sources and sensors capable of measuring sound, light, temperature, or movement, in addition to the many digital systems that interact with their environment by measuring analog signals from those transducers.