Three pipes 1, 2, 3 are connected as shown. If the total discharge for the system is 610 L/s and the friction factor f is equal for all pipes, then: 1 600 m-150 mm- Q₁ 2 Q3 3 A 480 m - 200 mm 750 m-100 mm What is the flow rate (in L/s) in pipe 2? 387 L/s 398 L/s None of the choices 361 L/s 3401 /s B

Three pipes 1, 2, 3 are connected as shown. If the total discharge for the system is 610 L/s and the friction factor f is equal for all pipes, then: 1 600 m-150 mm- Q₁ 2 Q3 3 A 480 m - 200 mm 750 m-100 mm What is the flow rate (in L/s) in pipe 2? 387 L/s 398 L/s None of the choices 361 L/s 3401 /s B

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

M MEQ2.jpg 200mmø 690mm 300 mm 400 mmø Z Hg (13.6) A 200mm diameter venturi meter is installed in a 400mm diameter vertical main pipe as shown. If the deflection of mercury (SG = 13.6) at the manometer reads 300mm and the vertical distance between point 1 and point 2 is 690mm, determine the discharge in the system assuming a head loss of 600mm. Hide answer choices a A) 307.36 L/s B) 279.84 L/s No Answer among the choices D) 224.67 L/s 256.29 L/s O O O O C
Q2- Water ( p= 990 kg/m' & µ= 0.001 pa.s) is pumping from a water tank to water injection well with carbon steel pipe at the same level, where the pipe diameter is 12 inch, pipe length is 4700 m, pipe roughness is 0.0000045 m, and water flow rate is 0.0065 m/sec. 1- Calculate discharge frictional head loss. 2- Calculate pump liquid power, if pump section head value is 3.8 m.
- Determine the total head loss hf from A to o in U the susem shown in the figure iF the discharge is |. G0 m ls. Assume f=002 for all pipes 450 mm &, G00m qoomm &, 900m 750mmo,450m IC GO mm & ,720m D
A pipe system has a discharge of 0.106 m'/s with n- 0.013. Length (m) Pipe Dia (mm0) 1 100 250 150 200 250 150
A liquid whose specific gravity is 2.0, is flowing in a 50mm diameter pipe. The total head at a given point was found to be 17.5m. That point is 3m above the datum and the pressure in the pipe is 65.6KPA. Compute the discharge in that point of the pipe. (A 19.28 L/s B No Answer among the choices 24.31 L/s D 29.05 L/s (E 32,56 L/s
Two pipes 1 and 2 are connected in parallel. Pipes 1 and 2 have the same length and diameter. If the flow in pipe 1 is 680 L/s and the friction factor in pipe 2 is twice of the friction factor of pipe 1, determine the discharge of pipe 2. A) 509 L/s B No Answer among the choices 530 L/s D) 460 L/s E) 481 L/s
- Dekrmine the total head loss hf. from Å to o in the systen shomwn in the figure iF the discharge is 1. G0 mls. Assume f=0:02 for all pipes 450 mm o, GO0 m 9oomm ở , 90 m 구5Dmmd,40m D GUD mm,720m
100mmgl 个一 680mm 320 mm I320m 300mm A H2O A vertical venturi meter 100mm diameter is installed in a 300mm diameter vertical pipe as shown. The flow is upward. If the specific gravity of the mercury at the bottom part of the manometer is 13.6, determine the a) Discharge neglecting head loss, b) Discharge if head loss from point 1 to point 2 is 500mm, and c) Coefficient of discharge (This is a multiple answer question. You must have 3 selected choices since there are 3 required answers in the problem) A No answer among the choices in question A B No answer among the choices in question C C = 0.819 D No answer among the choices in question B E) Q = 70.3 L/s Qt = 86.2 L/s G) Qt = 65.8 L/s H) Q = 86.2 L/s Q = 65.8 L/s C = 0.936 к) с30.753 Qt = 70.3 L/s M) C = 0.668 N) Qt = 57.6 L/s o Q = 57.6 L/s
Problem 4 Find the flowrate in each pipe. CH= 130 300 gpm Pipe AB BD DC AC с Diameter (in) Length (ft) 250 100 250 100 2.0 2.0 4.0 4.0 B D 190 gpm 110 gpm
The water surface shown below is 10 m above the datum. The pipe is 425 mm in diameter and the total loss of head between point (1) in the water surface and point (5) in the jet is 3 m. Determine the discharge Q. (m3/s). Round your answers in 3 decimal places.
Kerosene (s.g.-0.82) enters the cylindrical arrangement of the figure shown at section 1, at 0.56 N/s. The 125-mm-diameter plates are 3.2mm apart. Assuming steady flow, compute the inlet average velocity v1, outlet velocity v2 assuming radial flow, and outlet volume flux. D: 125mm D2: 3.20mm D1: 6.85mm
1.) For the water shooting out of the pipe and nozzle under the condition showed, find the height above the nozzle to which the water jet will "shoot". Assume negligible head loss. Water 1.100m 1 ORECA DE Nozzle D-100 mm Point A D-200 mm Pa- 55.0 hPa