M MEQ2 jpg 200mmø 690mm 300 mm 400 mmø Tit H20 LHg (13.6) A 200mm diameter venturi meter is installed in a 400mm diameter vertical main pipe as shown. If the deflection of mercury (SG = 13.6) at the manometer reads 300mm and the vertical distance between point 1 and point 2 is 690mm, determine the discharge in the system assuming a head loss of 600mm. Hide answer choices a A 307.36 L/s B) 279.84 L/s

M MEQ2 jpg 200mmø 690mm 300 mm 400 mmø Tit H20 LHg (13.6) A 200mm diameter venturi meter is installed in a 400mm diameter vertical main pipe as shown. If the deflection of mercury (SG = 13.6) at the manometer reads 300mm and the vertical distance between point 1 and point 2 is 690mm, determine the discharge in the system assuming a head loss of 600mm. Hide answer choices a A 307.36 L/s B) 279.84 L/s

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

200mmø 690mm 300 mm 400 mmø 金Ho0 Z Hg (13.6) A 200mm diameter venturi meter is installed in a 400mm diameter vertical main pipe as shown. If the deflection of mercury (SG = 13.6) at the manometer reads 300mm and the vertical distance between point 1 and point 2 is 690mm, determine the discharge in the system assuming a head loss of 600mm.
300 mme 100 mmø H20, 2) 500mm A 100mm diameter venturi meter is installed in a 300mm diameter horizontal main pipe as shown. If the deflection of mercury (SG = 13.6) at the manometer reads 500mm, determine the discharge in the system assuming a head loss of 700mm. (A) 82.84 L/S (B) 78.63 L/s No Answer among the choices (D) 87.68 L/s (E) 93.21 L/s
300 mmg 100 mmø H2O, 2) 500mm A 100mm diameter venturi meter is installed in a 300mm diameter horizontal main pipe as shown. If the deflection of mercury (SG = 13.6) at the manometer reads 500mm, determine the discharge in the system assuming no head loss.
600mm water diameter 300mm 1. diameter 02 150mm Mercury (SG = 13.6) A venturi meter with diameter of 300mm is attached to a 600mm main pipe and has its axis inclined downward as shown. a) Discharge if head loss is neglected is Blank 1 cu.m./s b) Discharge if head loss is 500mm from point 1 to 2 is Blank 2 cu.m./s c) Coefficient of discharge is Blank 3 The manometer shows a deflection of 15cm of mercury (SG =13.6). If the flowing fluid is water and direction is from 1 to 2, determine the
As shown in the figure below, a Venturi meter is installed on a 300-mm diameter pipe whose maximum flow is 125 liters per second and the pressure head is 6.5 m of water. Determine the minimum throat diameter that will give a negative head. Solve for the discharge that will pass through the meter when the double column differential mercury gauge connected to it will show a difference of 25 cm. |25сm P. 36.5 h A2 300mmф Al ANSWER: a. D = 118mm b. Q = 87 liters/sec
... 300 mmg 100 mmø H20, 500mm EHgC(13-6) A 100mm diameter venturi meter is installed in a 300mm diameter horizontal main pipe as shown. If the deflection of mercury (SG = 13.6) at the manometer reads 500mm, determine the discharge in the system assuming no head loss. (A) No Answer among the choices (B) 94.12 L/s 82.44 L/s 77.36 L/s (E) 87.86 L/s
This problem uses Figure 2. Select all that are true about this manometer set-up. Open Air Tank (A) (1) BU (4) Z₁ (2) (3) P₁-P₁=1²1 - 7222 P4 - PA = 71 (21 +22) P₁ = PA-1²1 + 72²2 PA = P₁ Y2
A Cole pitometer is set with its orifices at the center of a 40cm pipe. Determine the discharge if the deflection, z of carbon tetrachloride (s = 1.50) in the differential gauge is 325mm. Use C = 0.84 and the ratio of the mean velocity to center velocity may be assumed as 0.83. C4o cm
Determine the throat diameter of a Venturi meter to be introduced in a horizontalsection of a 100 mm diameter main so that the deflection of a differential mercurymanometer connected between the inlet and the throat is 600 mm when the dischargeis 20 l/s of water. The discharge coefficient of the meter is 0.95.
600mm water diameter 300mm diameter 150mm Mercury (SG = 13.6) %3D A venturi meter with diameter of 300mm is attached to a 600mm main pipe and has its axis inclined downward as shown. The manometer shows a deflection of 15cm of mercury (SG =13.6). If the flowing fluid is water and direction is from 1 to 2, determine the a) Discharge if head loss is neglected is Blank 1 cu.m./s b) Discharge if head loss is 500mm from point 1 to 2 is Blank 2 cu.m./s c) Coefficient of discharge is Blank 3 Blank 1 Add your answer Blank 2 Add your answer Blank 3 Add your answer
200mmø 690mm 300mm 400 mmø LHg (13.6) A 200mm diameter venturi meter is installed in a 400mm diameter vertical main pipe as shown. If the deflection of mercury (SG = 13.6) at the manometer reads 300mm and the vertical distance between point 1 and point 2 is 690mm, determine the discharge in the system assuming a head loss of 600mm. (A) 224.67 L/s B) 256.29 L/s c) No Answer among the choices (D 279.84 L/s E 307.36 L/s
This problem uses Figure 2 L. Select all that are true about this manometer set-up. Open (A) - Y1 (2) hị (1) Y2 P2 - PA = Yıhı – y2h2 O P2 = PA – Y1 hị + y2h2 ) P2 – PA = Y1 (hị + h2) P2 = 0