Three loads are connected in parallel across a 1400-V rms, 60-Hz single-phasesupply as shown in Figure 2.8.I111213Load 1: Inductive load, 125 kVA at 0.28 power factor.Load 2: Capacitive load, 10 kW and 40 kvar.1400 V123Load 3: Resistive load of 15 kW.(a) Find the total kW, kvar, kVA, and the supply power factor.(b) A capacitor of negligible resistance is connected in parallel with the above loadsto improve the power factor to 0.8 lagging. Determine the kvar rating of this ca-pacitor and the capacitance in μF.

Answered: Three loads are connected in parallel…

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

In a balanced three-phase delta-connected source, if the line voltage magnitude is 110 V, what is the phase voltage magnitude? O 190.5 V O 110 V O 63.5 V O OV
A Single Area consists of 3 generating units (G1/G2/G3) with the following characteristics: G1: 200 MVA rating, R1 = 0.025 pu (on the 200 MVA base), initial output P1 = 150 MW. G2: 300 MVA rating, R2 = 0.01 pu (on the 300 MVA base), initial output P2 = 200 MW. G3: 400 MVA rating, R3 = 0.02 pu (on the 400 MVA base), initial output P3 = 300 MW. The frequency of the system is 60 Hz. Assuming D = 0.75 pu on a common base of 1000 MVA, what is the new generation output for G1 for a load increase of 150 MW? Select one: O a. None of these O b. 252.12 MW O c. 155.45 MW O d. 170.42 MW
A d.c. serier generator, having an external characteristic which is a straight line through zero to 50 V 200 A is connected as a booster between a station bus bar and a feeder of 0.3 ohm resistane. Calculate the voltage difference between the station bus-bar and the far end of the feeder qa current of (i) 200 A and (ii) 50 A.
If the load is connected to the generator thgrough an inductive line and the voltage at the load side is the same as the voltage at the terminals of the generator, which of the following must be true? O A. The reactive power is flowing from the generator to the load and from load to the generator at the same time. O B. The load is disconnected, and no power is delivered to the load. O C. The load has a poor power factor and it's absorbing too much reactive power. O D. None of the other choices are correct O E. The generator is unable to produce reactive power; therefore, the reactive power is flowing from the load to the generator.
A Single Area consists of 3 generating units (G1/G2/G3) with the following characteristics: G1: 250 MVA rating, R1 = 0.02 pu (on the 250 MVA base), initial output P1 = 200 MW. G2: 350 MVA rating, R2 = 0.015 pu (on the 350 MVA base), initial output P2 = 300 MW. 0.03 pu (on the 300 MVA base), initial output P3 = 150 MW. G3: 300 MVA rating, R3 = The frequency of the system is 60 Hz. Assuming D = 1 pu on a common base of 1000 MVA, what is the new generation output for G3 for a load increase of 75 MW? Select one: O a. 190.55 MW O b. None of these O c. 203.38 MW d. 166.01 MW
Q)The question is that how kW is converted to kVA in complex form and how kV square is 2.4 for T1,T2,T3 can you plz explain it by seeing the solution
Two relays each with 20-ohm resistance and 0.16-henry inductance are connected in series. What is the equivalent impedance?a. 20 + j102.2 ohms c. 20 + j95.32 ohmsb. 20 + j120.63 ohms d. 10 + j25.32 ohms
Describe the concept of three-phase power in electrical systems and its significance in power distribution.
A three-phase system has balanced conditions so that the per-phase circuit representation can be used as shown in Figure 1 Select the turns ratio of the step-up and step-down transformers that the system operates with an efficiency greater than 99 percent. Moreover, find the complex power (received or given) of all components in the circuit and the V1 and V2 voltages. The load voltage is specified as 4 kV rms, and the load impedance is 4/3 ohm. ..
Two transformersA and B are connected in parallel to a load of (2+j1.5) ohm.Their impedances in Secondary terms ZA = (0.15+j0.8) ohm and Zb = (0.1+j30.6)ohm Their no-load termind voltages are EA=200<0 V and EB=210<0 Volt.Find the power and Power factor of each transformer? %3D %3D
3. A circuit consists of two impedances. Z1 =20230° and Z2 =25260° 2, in parallel, supplied by a source voltage V=1002600 volts. Determine the power triangle for each of the impedances and for the source.

Recommended textbooks for you

Introductory Circuit Analysis (13th Edition)

Electrical Engineering

ISBN:

9780133923605

Author:

Robert L. Boylestad

Publisher:

PEARSON

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Programmable Logic Controllers

Electrical Engineering

ISBN:

9780073373843

Author:

Frank D. Petruzella

Publisher:

McGraw-Hill Education

Introductory Circuit Analysis (13th Edition)

Electrical Engineering

ISBN:

9780133923605

Author:

Robert L. Boylestad

Publisher:

PEARSON

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Programmable Logic Controllers

Electrical Engineering

ISBN:

9780073373843

Author:

Frank D. Petruzella

Publisher:

McGraw-Hill Education

Fundamentals of Electric Circuits

Electrical Engineering

ISBN:

9780078028229

Author:

Charles K Alexander, Matthew Sadiku

Publisher:

McGraw-Hill Education

Electric Circuits. (11th Edition)

Electrical Engineering

ISBN:

9780134746968

Author:

James W. Nilsson, Susan Riedel

Publisher:

PEARSON

Engineering Electromagnetics

Electrical Engineering

ISBN:

9780078028151

Author:

Hayt, William H. (william Hart), Jr, BUCK, John A.

Publisher:

Mcgraw-hill Education,

SEE MORE TEXTBOOKS