The strut is supported by a pin at C and an A-36 stoel guy wire AB. (Eguce.1) Part A If the wire has a diameter of 4.8 mm, determine how much it stretches when the distrbuted load acts on the strut. Express your answer three to significant figures and include the appropriate units. HA ? Value mm Figure 1 of 1 Submit Previous Answer Beauest Answer X Incorrect; Try Again; One attempt remaining 60 Provide Feedback Next> JAAN

Q: If load P = 20.1 kips, determine the normal force in bar (1). A 6 ft 46.6 kips 39.5 kips 33.5 kips…

A:

Q: To test the deflection on a uniform 100-kg beam, a boy of who weighs 50 kg exerts a pull of 150N on…

A:

Q: The axial stress on the cross-section of the aluminum rod between A and C is ___ ksi. b). The…

A:

Q: Using the method of joints, determine the magnitude of force (Ib) in member AC of the truss shown if…

A:

Q: Question The bar is subjected to the axial load. There is a shaded section which is oriented at 0…

A: Given:A=0.02 m2P=255 KNθ=25°

Q: art ● pus ents es Three cables having an area of 0.05 in² each is carrying the load W as shown. With…

A: To find: The stress in longest cable. Given: The load is W=1500 lb. The length of the three cables…

Q: Determine the force in each member of the loaded truss. The forces are positive if in tension,…

A:

Q: The allowable tensile stress for wires AB and AC is ơallow = 210 MPa, and wire AB has a diameter of…

A: Given data:-Allowable stress in wire AB & AC=σABallow=σACallow=210MPadiameter of wire AB,…

Q: Engineering Mechanics Rate will be given! Please write the complete solutions legibly. Box the…

A:

Q: Q1: Determine the thickness of the plate or plate with a width of 100mm to ensure safe continuous…

A: Given data  Width=100mm Maximum tensile load=300kN Minimum value of load = 150kN The bearing…

Q: Determine the force in each member of the loaded truss. The forces are positive if in tension,…

A: Given data: ◆ The force applied at the joint D: F = 2140 N ◆ The dimensions of truss: a = 3.3 m, b =…

Q: Determine the magnitude of force (kN) in member BC if F=60394 N , a=3.76m, b=1.27m and c=4.52m.…

A:

Q: Determine the magnitude of force (kN) in member AC if F=84757 N , a=3.78m , b=1.28m and c=4.61m.…

A:

Q: Material A and Material B are tested in tension Material A is loaded to the proportional limit which…

A: Since we know that, the resilience of the body is the total energy absorbed by it before fracture…

Q: A rigid horizontal bar ABC is supported by three vertical rods as shown. The system is stress free…

A:

Q: Use the method of sections to determine the axial forces in the members DF, EF and EG of the armor…

A: Use the method of sections to determine the axial forces in the members DF, EF and EG of the armor…

Q: (2) For the truss loaded and supported As shown, use the Method of Sections to compute the ff: 0.9…

A:

Q: 19. A 200 lb force P is exerted on the lever. What will be the deformation, in inches, in the 0.0630…

A: This question is based on the concept of deformation. As per the guidelines we are subjected to…

Q: 12. A column of length 18" and a diameter of 0.25" was tested with both ends pinned. The measured…

A: Given- Length (L) = 18  inch Diameter (d)  = 0.25 inch E = 29000 ksi = 29000000 lbs/in2 Case 1 -…

Q: Determine the magnitude of the load on the worst loaded rivet

A: Given: A horizontal plate has been joined to a vertical post using four rivets as shown in figure:…

Q: The length of the cable segment AB is 10 ft (Eigure 1) The angle a = 30° ▼ Part A What force T is…

A: The length of AB is .The angle is The weight of crate is

Q: Find the force CD. The force is positive if in tension, negative if in compression.

A:

Q: Learning Goal: As shown, two composite columns of steel and concrete are used to support a rigid…

A:

Q: Required Information NOTE: This is a multi-part question. Once an answer is submitted, you will be…

A: L= 1.2 kN To find - The forces in members.

Q: Determine the  magnitude of  force (kN) in member BC if F=66188 N , a=2.75m , b=1.15m and c=4.11m.…

A:

Q: THE MAGNITUDE OF THE DISTRIBUTED FORCE (w=X+X+X+X_kN/m) WILL BE THE SUMMATION OF ALL THE NUMBERS IN…

A:

Q: The rod is subjected to the linearly varying axial distributed load as shown. What is the correct…

A:

Q: ! Required information A 4.8-ft-long steel wire of 1/4 in. diameter is subjected to a 774-lb tensile…

A: According to the given data D=0.25in L=4.8ft E=-29x106psi P=774lb We need to find  The normal stress

Q: Given: Find: A 0.5-inch diameter pole (L1-12 in, L2= 22 in) is loaded with three forces (two forces…

A: Pole diameter, D = 0.5 inch  L1 = 12 in, L2 = 22 in  P1 = 2.5 kip or 2500 lbs  P2 = 7 kip or 7000…

Q: Use the Method of Sections to find the load in member EK of the bridge. Is it in tension or…

A:

Q: Using the method of joints, determine the magnitude of force (Ib) in member AC of the truss shown if…

A:

Q: Please answer both 1 and 2 as they relate to eachother. thank you in advance

A: Write the properties of 1040 steel.

Q: Determine the magnitude of the force (Ib) in member BD of the truss shown if P = 34866 lb, Q = 34907…

A:

Q: Determine the magnitude of force (kN) in member AC if F=70865 N , a=3.37m , b=1.0 and c=4.28m. Round…

A:

Q: For the truss and loading shown, determine most economical cross-sectional area (in in2) of member…

A:

Q: Determine the magnitude of the force (Ib) in member CD of the truss shown if P = 31206 Ib, Q = 35817…

A:

Q: P=670 lb a=1.5 in b=0.5 in. c=1.0 in. d= 2.0 in What is the average shear stress in the wood…

A:

Q: Using the method of joints, determine the magnitude of force (Ib) in member AD of the truss shown if…

A:

Q: Using the method of joints, determine the magnitude of force (Ib) in member AD of the truss shown if…

A:

Q: NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to…

A: To find force in member CH and left of it

Q: 1.5 m 1.5 m 1.5 m PV B -2 m – -2 m –

A: Given , P = 10 KN