The working substance for a Carnot cycle is 8 lb of air. The volume at the beginning of isothermal expansion is 9 cu ft and the pressure is 300 psia. The ratio of expansion during the addition of heat is 2 and the temperature of the cold body is 90°F. Find: Pm (Mean Effective Pressure) in Psia

Q: A helical compression spring of 10 coils, dw=1mm, dm = 14 mm, P = 3mm, G= 80 GPa. Find (K), (U) and…

A:

Q: O 32,3 m a) Find the irreversible head loss of the system 22,8 m 29,7 m 25,4 m 26,7 m b) Since the…

A: For solution refer below images.

Q: Required information A 24-mm-diameter uniform steel shaft is 600 mm long between bearings. Take the…

A: the diameter of the steel rod d = 24 mm = 0.024 mthe length of the steel rod l = 600 mm = 0.6 mthe…

Q: I Review Part A- Transmitted power Learning Goal: To determine the maximum possible power…

A:

Q: A 4.8 m long from fixed point, 0.5 m wide and assumed a thickness of 30 mm throughout a springboard…

A: “Since you have posted a question with multiple sub parts, we will provide the solution only to the…

Q: write INTRODUCTION about Finite Element Spanner Design

A: Introduction about finite Element Spanner Design

Q: 3. During tug of war, the bicep muscle generated 4k N force that was perpendicular to the forearm…

A:

Q: * The unit of measurement for torque is

A:

Q: 2. what is the reduction ratio, if D.-94mm, this means r=47mm=0.047m If pressure (P) = 45Mpa (45*106…

A: given data  initial diameter = 94 mm final diameter = 16 mm pressure = 45 Mpa.

Q: 1. Fig. 1 shows a simple six bar linkage held in static equilibrium while a force P= 750 N is…

A:

Q: A RWD Formula SAE car is given with the following information m = 600 lbm (including the driver), l=…

A:

Q: Q-4: Four-stroke, single-cylinder diesel power unit when tested gave the following particulars:…

A:

Q: - The corrected length of tape. - The true length of the line.

A:

Q: w(x) = 24VX N/m %3D 96 N/m A B 370 What is the resultant force of the distributed load?

A:

Q: How to rearrange equation to solve for r3? q/L = 468.09 W/m r2 = 18 x 10-3 m

A: Given: q/L = 468.09 W/m r2 = 18 x 10-3 m and equation as, qL=236lnr3r20.5+0.0819 Solve the value of…

Q: The table gives data concerning the shrink fit of two cylinders of differing materials and…

A:

Q: Two L6 x 6 x 1 equal leg angles (see Table A-7) are attached back-to-back to form a T-section, as…

A: The maximum allowable stress is

Q: Units: mmgs Mass = 538.9662 grams Volume = 199617.1105 cubic millimeters Surface area = 32076.7718…

A: It is asked to draw the model shown below

Q: is it correct?? if it is correct,please tell me why r=0,z=H??

A: We have given in the solution:To find:Whether the Boundary condition applied r=0,Z=H are correct or…

Q: A 200 MPa 100 MPa 150 MPa

A: Given Data

Q: Solu for gap {d). Given: 11- 198.15 K T2= 315.15 K Steel irils e 40 mm Sterl rails lincar expansion…

A:

Q: Figure Q2 shows a beam subjected to distributed loading. Knowing the beam is fixed supported at one…

A: a) Free body diagram of the beam The free body diagram of the given beam is where, RB is the…

Q: Estimate the heat loss from human body of 36 C temperature by convection and radiation. Consider the…

A: The heat loss from human body of 36oC temperature by convection and radiation is 304.875 W.

Q: Task III Based on Figure 3. Use the D’Alembert's principle to determine the following knowing that…

A:

Q: Determine which rigid body experiences complex motion Locate the instant center for that rigid body…

A:

Q: Find force value Work done=1001 J Displacement=50 m

A: Given data : Displacement=d Work done=W   To find : Force

Q: PROBLEM 3: The coefficients of friction between the block and the rail are µ, and µg. Determine the…

A:

Q: Find force value

A: Given data : Displacement=d Work done=W   Required : Force

Q: Spring index is: (where: OD = The outside diameter, ID = the inside diameter, Dw the wire diameter,…

A:

Q: An engine cylinder has a compression ratio (r) of 7.5, a clearance volume of 35 cm³ and a piston…

A:

Q: Find the Shear and Bending Moment Diagrams.

A:

Q: has a compression ratio (r) of 7.5, a clearance volume of 35 cm3 and a piston stroke length of 325…

A:

Q: 1 8 1/4' 1/4 3/8 ASTM - A-36 STEEL Temperature changes from 32°F to 685 F F= 375.000 lbs. 20 F=…

A: dimension of the beam web dimension =applied load F=375000 lbslength of the beam L= 20ftinitial…

Q: What would an isometric of the oxygen piping system below look like, where PSA GEN = Pressure Swing…

A: can outline a general arrangement for the piping system:PSA GEN (Pressure Swing Adsorption Oxygen…

Q: Referring to the figure shown below, water contained in a piston-cylinder assembly, initially at 1.5…

A:

Q: If a DC motor with 83% efficiency requires a current supply of 213 mA at 250 rpm. What should be the…

A: Given: η = 83%I = 213 *10-3 APin=1.5  WN = 250 rpm

Q: y-axis 6m 6m >X-axis 12m

A: To determine the centroid of the given figure.

Q: The force on the inside of a cork in a champagne bottle is 20 pound-force [lb,]. If the cork has a…

A: Given: The force inside the champagne bottle is F=20 lbf. The diameter of the cork is d=0.5 in.…

Q: Wi Wz _F STEM PART 1 TAB TAB STEM TAB TAB PART2 BY NC SA 2014 Michael Swanbom Dimensions: WĄ W2 W3…

A: Stress is the ratio of force and area.

Properties of Fluids

The term fluid represents a type of substance that can easily change its shape under any external pressure/force and can flow. Fluids can acquire any shape in which it is stored and can resist normal stresses but cannot resist shear stress in rest condition. Whenever external shear stress is applied to fluids, it starts to flow. The fluids may be liquid or gas. Example- water, air, etc.