The winding drum of mass 300kg has an effective diameter of 950mm and radius of gyrationof 650mm. The drum is driven by a motor whose efficiency is 80% through a gear reduction of 20:1. Determine motor torque when the load ia accelerated at 4 meters per squared second and maximum uniform speed of the rock, if the maximum power output of the motor is 18KW?

The winding drum of mass 300kg has an effective diameter of 950mm and radius of gyrationof 650mm. The drum is driven by a motor whose efficiency is 80% through a gear reduction of 20:1. Determine motor torque when the load ia accelerated at 4 meters per squared second and maximum uniform speed of the rock, if the maximum power output of the motor is 18KW?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

i need the answer quickly
The wheel has a mass of 100 kg and a radius of gyration of ko = 0.2 m. A motor supplies a torque M = (400 +900) N - m where is in radians, about the drive shaft at O. Initially the car is at rest when s = 0 and 0 = 0°. Neglect the mass of the attached cable and the mass of the car's wheels. (Figure 1) Figure 94°F Sunny M KI 0.3 m 1 of 1 Pro
A wheel is attached by a cable to a block The wheel has a radius of 2ft and weighs 300lbs, the block weights 20lbs. If the radius of gyration about the point of rotation of the disk is 1.5ft, how many revolutions will it take for the wheel to come to a stop assuming it was moving at 10 rad/s CW. Assume the block is on the left side of the wheel and thus causes a CCW moment.
A reciprocating engine runs at 110 rpm with a stroke of 1.6 m and a connecting rod 2.4 m in length. It imparts simple harmonic motion to a 250 mm diameter piston. When the crank pin is 32º beyond top dead centre the pressure on the piston is 0.8 MN/m². Calculate EACH of the following: (a) the instantaneous velocity of the piston; (b) the instantaneous torque at the crank pin; (c) the instantaneous acceleration of the piston.
Pls ans all
2. Determine the blade radius, twist and chord distributions for a 2-bladed rotor that will produce a rated power 150 kW.
A flywheel of mass 125kg and radius of gyration 150mm is accelerated from rest to a speed of 1180rpm whilst making 500 revolutions. The motion is resisted by a friction torque of 2.5Nm. Determine the work done and the maximum power developed by the driving motor.
Vipretion
A pair of rods and disc form a triangle with a spring (a spring connects A to C). The spring has a spring constant of 20 N/m and an unstretched length of 1.5m. each rod has a length of 3m and a mass of 10kg. The disk has a mass of 5kg, a radius of .5 and rolls without slipping. The system starts with an angle between the spring and rods of 60 degrees, determine the angular velocity of the rods after it has dropped to a 30 degree angle.
The accelerating torque increases the speed of a flywheel from x rpm to y rpm in 15 seconds. Find 1. The accelerating torque produced during the above period. 2. Increase in the kinetic energy of the flywheel 3. Change in the angular momentum of the flywheel. 4. Number of revolutions made by the flywheel during this period. 5. Find the braking torque required to stop the flywheel completely. Assume suitable mass and radius of gyration. Also assume suitable values for rpm x and y above.
I need unique and correct answer. Don't try to copy from anywhere. Do not give answer in image formet and hand writing
Solve correctly! Use image down below and pay attention to the numbers that it’s using UNITS SHOULD BE (m/sec) use the correct units!!!