Solve for given solution The Wheels of a standard bicycle have a rolling radius of approximately 15 inches and a radius to the centerof the caliper disk brake pads of 13.5 inches. The combined weight of the bike plus the rider is 260 lb, whichis equally distributed between the wheels. If the coefficient of friction between the tires and the road surfaceis twice that between the brake pads and the metal wheel rim, what clamping force must be exerted by thecalipers in order to slide the wheels?Ans. Fc 144.4 lb

Step 1: Calculate total weight on each wheel Given the total weight of the bicycle plus the rider is…

Answered: The Wheels of a standard bicycle have a…

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.72P

See similar textbooks

Similar questions

A uniform plank is supported by a fixed support at A and a drum at B that rotates clockwise. The coefficients of static and kinetic friction for the two points of contact are as shown. Determine whether the plank moves from the position shown if (a) the plank is placed in position before the drum is set in motion; and (b) the plank is first placed on the support at A and then lowered onto the drum, which is already rotating.
Two identical chairs, each weighing 14 lb, are stacked as shown. The center of gravity of each chair is denoted by G. The coefficient of static friction is 0.2 at B (the contact point between the chairs) and 0.35 at A, C, and D. Determine the smallest force P that would cause sliding.
The 40-lb spool is suspended from the hanger GA and rests against a vertical wall. The center of gravity of the spool is at G and the weight of the hanger is negligible. The wire wound around the hub of the spool is extracted by pulling its end with the force P. If the coefficient of static friction between the spool and the wall is 0.25, determine the smallest P that will extract the wire.
The brake pads at C and D are pressed against the cylinder by the spring BF. The coefficient of static friction between each pad and the cylinder is 0.15. Find the smallest tension in the spring that would prevent the cylinder from rotating when the clockwise couple M=2200lbin. is applied. Neglect the weights of the members.
The blocks A and B of weights WA and WB are joined by a rope that passes over the fixed peg C. The coefficients of static friction are =0.2 between block A and the inclined plane, and =0.25 between the rope and the peg. Determine the range of Wb/WA for which the system will be in equilibrium.
The coeffient of static friction between the uniform bar AB of weight W and the ground is 0.45. Find the smallest angle and the corresponding force P that would initiate simultaneous tipping and sliding of the bar.
The cone clutch transmits the torque C through a conical friction surface with cone angle . The inner and outer radii of the friction surface are a and b, respectively. The left half of the clutch is keyed to the shaft, and the right half drives a machine (not shown) through a gear attached to its outer rim. Assuming uniform pressure on the friction surface, show that the maximum torque that can be transmitted by the clutch is
The contact surface between the 36-lb block and 20-lb homogenous cylinder is frictionless. Can the system be in static equilibrium 0n the rough inclined plane?
The two homogeneous bars AB and BC are connected with a pin at B and placed between rough vertical walls. If the coefficient of static friction between each bar and the wall is 0.25, determine the largest angle 6 for which the assembly will remain at rest.
The mass of the unbalanced disk is m, and its center of gravity is located at G. If the coefficient of static friction is 0.2 between the cylinder and the inclined surface, determine whether the cylinder can be at rest in the position shown. Note that the string AB is parallel to the incline.

Recommended textbooks for you

International Edition---engineering Mechanics: St…

Mechanical Engineering

ISBN:

9781305501607

Author:

Andrew Pytel And Jaan Kiusalaas

Publisher:

CENGAGE L