The value of R2

Q: Reduce the diagram to a single block G2 64

A: to reduce the given block diagram

Q: (s) G₁ H₁ G₂ Hy G3 H₂ G₁ C(s)

A:

Q: Q1 : Which Battery is discharging and which one is charging ? and why ?

A: As per the company policy, only 1st question will be answered. Here we discuss about the mesh…

Q: 5. Determine the total resistance if each R is 30. O RT M -W

A:

Q: Draw the circuit and solve. The potential difference across the terminals of a battery is 10 V when…

A: By ohms law current in resistor =Voltage across resistorresistance. using two two conditions…

Q: H, G: G4 H:

A:

Q: What happens when C2 is removed and why?

A: Removing capacitor C2 from the circuit will likely affect the filtering performance of the circuit,…

Q: H3 G, G2 G3 R H2

A:

Q: EX Find is, in the circuit below"

A:

Q: R2 R4 1.5 k2 10 kQ VT R1 R3 10 kQ R5 15 k2 36 V 15 k2 R7 R6 1 kQ 5 kQ

A: To find the current and voltage across each resistor

Q: -. A block diagram is shown in the following figure, try to calculate C/R. G₁ H₁ H₂ G₂ G3

A:

Q: Using the circuit below, determine the following: a. the voltage-drop across R1 b. the Power taken…

A: This question belongs to circuit theory . It is based on the concept of voltage division and current…

Q: G2 G1 R H1

A:

Q: a1/ What is the maximum current that can flowin the circuit shown below when taking into account the…

A: The maximum current can flow in the condition when the total resistance is minimum. and the total…

Q: Determine the response function V2/ VI. What would you call the behavior of this circuit?

A:

Q: Reduce the flowing block diagram: H3 (s) G1 G2 G3

A:

Q: In the circuit below, the currents through the four resistors are as indicated. Use the junction…

A: Given the circuit,

Q: Find Reg when the switch is open. Repeat when the switch is closed. R2 200 R1 100 R3 50 Seg

A: To solve above problem, one should know how to find equivalent resistance for series and parallel…

Q: I need help building this BJT amp circuit on a breadboard. If possible would you be able to show how…

A: Need to provide the Breadboard layout for the given Voltage divider biased BJT circuit.

Q: Do D1 D2 D3 EE

A: For a 4×1 Multiplexer, the output Y is given as

Q: R1 6 k2 2-D APPROXIMATION RL 1 k2 Vs ty 3 k2 36 V

A: Given:

Q: 220N 500N 1202 В

A:

Q: 4 Construct state graph for the Circuiti- state table and given

A:

Q: If two resistances of 10 Q and 5 Q are connected in parallel. Find equivalent resistance. а. 33.33 m…

A: When two resistance R1,R2 are in parallel Equivalent Resistance R= (R1*R2)/(R1+R2) R=(10*5)/(10+5)…

Q: P-2.7. Find the final form of T.F. (E.) Ei) for the following Circuit :

A:

Q: Why is the circuit critically damped? Explain.

A:

Q: B) A strain gauge has a resistance of 1000 2 is connected as a one arm of a whetstone bridge to…

A: The solution can be achieved as follows.

Q: The next seven questions pertain to the situation described below. A circuit is constructed with…

A:

Q: In the circuit, here, the value of R1=10 k and R2=170 kn. What is the gain of the circuit to 2…

A:

Q: G4 C(s) G6 R(s) G1 G2 G3 H1 G5 H2

A:

Q: Reduce to a single block by using a. Moving Blocks and basic block configuration b. Mason's Rule…

A:

Q: R2 0.6 A R1 R2 4.9 V

A: According to ohms law current in resistor=Voltage across resistanceresistance 4.9 voltage source is…

Q: R(s) G6 G₁ G₂ H₁ H₂ G3 G5 G4 C(=

A: Given Data: A block diagram model of a system having, Input =Rs Output =Cs To Find: Block diagram…

Q: Q2/ Reduce the following system by using Masson's method: G Hs G G2 G4 Gs Hi H2 H5 H,

A: Given:

Q: 2. Refer to the circuit of Flg. 7-1.4 (loaded voltage divider). Explain what would happen to the…

A:

Q: M[B4]: Two resistors R1 and R2 are connected in parallel in an electric circuit. If the resistance…

A:

Q: 2K R1 RS R7 R10 3K 7K 10K R4 R11 R12 12K 4K BK RS SK R9 OK R14 14K R13 13K R1 R1 R1 R1 R1 R1 R2 R3…

A:

Q: Figure 1 shows the internal circuitry for a digital watch prototype. You, the engineer, are required…

A: Norton's equivalent circuit

Q: In the circuit below, the currents through the four resistors are as indicated. Use the junction…

A: The given circuit diagram is shown below, Using  I4, I5 and I6

Q: Write the mathematical representation of the circuit.

A:

Q: What is the K2 value?

A: Types of control system  Closed loop system  Open loop system

Q: Data collection Voltage: 20.1W Current: T1 T2 T3 T4 T5 T6 T7 52.6 C 50.3 C 48.1 C 37.0С 27.4 C 26.4…

A: Resistors, inductors and capacitors form an integral part of any electrical circuit. A source,…

Voltage Division Method

In the electronics branch, a voltage divider is required to produce a section of its input voltage as an output. This basic circuit may be prepared with two resistors or any passive elements along with the voltage source. The circuit resistors are attached in series and a voltage source is braced across these resistors. The input voltage can be transferred between the resistors in the circuit for the voltage division to occur. The SI unit of electrical resistance is ohm (Ω) or kilo-ohms (kΩ).