The uniform 120kg wide flange steel beam ABC is hanging initially at rest with 8=0 when the constant force P = 500N is applied to the cable BD, as shown in Figure Q1. Note: The mass moment of inertia about an axis perpendicular to the beam and passing through the pin at A, l = 1/3 mL.². 4 m 30 1.5 m 4m Figure Q1 -P a) Draw the free body diagram for the wide flange steel beam ABC. (CO1-PO1) (C2) b) Using Newton's Second Law of rotation, calculate the angular acceleration produced by the beam, and angular velocity of the beam after 10 seconds. (CO1-PO1) (C4)

The uniform 120kg wide flange steel beam ABC is hanging initially at rest with 8=0 when the constant force P = 500N is applied to the cable BD, as shown in Figure Q1. Note: The mass moment of inertia about an axis perpendicular to the beam and passing through the pin at A, l = 1/3 mL.². 4 m 30 1.5 m 4m Figure Q1 -P a) Draw the free body diagram for the wide flange steel beam ABC. (CO1-PO1) (C2) b) Using Newton's Second Law of rotation, calculate the angular acceleration produced by the beam, and angular velocity of the beam after 10 seconds. (CO1-PO1) (C4)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Use the graphical method to construct the shear-force and bending-moment diagrams for the beam shown. Let a = 5 m, b = 3 m, PB = 55 kN, Pc = 75 kN, and PE = 25 kN. Construct the shear-force and bending-moment diagrams on paper and use the results to answer the questions in the subsequent parts of this GO exercise. a PB Answer: Ay = i BO PB a B Pc a Calculate the reaction forces Ay and Dy acting on the beam. Positive values for the reactions are indicated by the directions of the red arrows shown on the free-body diagram below. (Note: Since Ax = 0, it has been omitted from the free-body diagram.) D Pc D a D₂ PE a PE E kN, Dy= i -x E X kN.
2:35 ll Solution and proble... 5/101 Determine the reactions at A and B for the beam subjected to the uniform load distribution. 4 kN/m B 300 mm -500 mm Problem 5/101 5/102 Calculate the support reactions at A and B for the loaded beam. 100 lb/ft 80 lb Problem 5/102 5/106 Determine the reactions at the supports of the beam which is loaded as shown. 800 N/m 400 N/m
A uniform plank of length 2.00 m and mass 35.0 kg is supported by three ropes, as indicated by the blue vectors in the figure below. Find the tension in each rope when a 675-N person is d = 0.500 m from the left end.
For the beam and loading shown in Figure 5, determine the value of (r) at the point of action of the resuitant force of the distributed load using point B as the origin. Parabola Vertex 2000 N/m 900 N/m B 6 m A Figure 5: A parabolic distributed load on a beam AB. Answer: If the loading were analysed using point A as the origin, would the value of w at the location of the resultant change? Select one: a. No b. Yes
A storage rack to hold the paper roll. Find force reactions and draw the shear and moment diagrams for the mandrel that extends half of the roll. Use singularity functions for this problem. Givens stanchion paper roll Density=984 kg/m^-3 OD=1.5 m ID=0.22 m L=3.23 m Density=mass/volume So W=(density*volume)*gravity Volume of hollow cylinder= (pi/4)(OD^2-ID^2)*Length of cylinder Length of mandrel=1/2 of L=>1.615 m mandrel base Assumptions: The storage rack is acting with a fixed support With a distributed load of "w" where w is the weight distrubuted
Part B: The Steel beam in Figure b is supported by a ball and socket at D and supported by separate cables at B. If the tension in cable BA and BC is 7500N and 4500N, respectively, determine: a) The components of the i, j, and k components of the resultant force at point B using unit vector notation. b) Assume the mass of the beam is concentrated mid-span, calculate the mass of the beam. 1500 mm A 10000 mm 3000 mm 550 mm B 1650 mm NE
Use the graphical method to construct the shear-force and bending-moment diagrams for the beam shown. Let a=4.0 ft, b-9.0 ft. c=4.0 ft, d=3.0ft, w=8 kips/ft and P = 66 kips. Construct the shear-force and bending-moment diagrams on paper and use the results to answer the questions in the subsequent parts of this GO exercise. B B ÎÎÎÎÎÎ Answers: Ay=i b d For this loading, calculate the reaction forces Ay and Ey acting on the beam. Positive values for the reactions are indicated by the directions of the red arrows shown on the free-body diagram below. (Note: Since Ax = 0, it has been omitted from the free-body diagram.) W C b C C D E kips, Ey = i E X Ey kips.
8:30 Test 3.pdf F1 F2 a CF3 A b a F4 D Consider the following values: - F5 a = 12 m; b = 10 m; c = 10 m; d = 8 m; F1 = 6 kN; F2 = 7 kN; F3 = 8 kN; F4 = 9 kN; F5 = 10 kN; a = 30°, 0= 45° , B = 60° 1] What is the resultant moment of the five forces acting on the rod about point A? a) - 111.6 kN.m b) 112.6 kN.m e) - 184.6 kN.m d) - 109.6 kN.m e) - 104.1 kN.m 0 None of them 21 What is the resultant moment of the five forces acting on the rod about point B? a) -95.8 KN.m b) 42.7 kN.m c) 80.9 kN.m d) 10.9 kN.m e) 51.8 kN.m ) None of them 31 What is the resultant moment of the five forces acting on the rod about point C? b) - 21.1 kN.m e) 17.4 kN.m d) - 16.5 kN.m e) 15.6 kN.m ) None of them a) 32.6 kN.m 4] What is the resultant moment of the five forces acting on the rod about point D? a) 37.6 kN.m b) 73.8 kN.m c) 71.6 kN.m d) 52.1 kN.m e) 21.1 kN.m ) None of them 5] What is the moment of the force F2 about point E? a) 90.7 kN.m b) - 88.1 kN.m c) 54.6 kN.m d) 103.1 kN.m e) 100.7 kN.m ) None…
An object is formed by attaching a uniform, thin rod with a mass of mr = 6.86 kg and length L = 5.76 m to a uniform sphere with mass ms = 34.3 kg and radius R = 1.44 m. Note ms = 5mr and L = 4R. 1) What is the moment of inertia of the object about an axis at the left end of the rod? kg-m2 2) If the object is fixed at the left end of the rod, what is the angular acceleration if a force F = 463 N is exerted perpendicular to the rod at the center of the rod? rad/s2
Assignment: In the figure shown below, a boom AC is supported by a ball and socket joint at C and by the cables BE and AD. If the force multiplier of a force F acting from B to E is Fm = 10lb/ft. Find the component of F that is perpendicular to the plane DAC. 6 10'1 W Analysis: FIDAC = F• nDAC СА х CD СА х CD îDAC
D 40.0 cg 30.0⁰ H 2.0 m draw the free body diagram. draw the vector starting at the black dogs. The location and orientation matter. A uniform, 3.0 m, 1250 kg beam is hinged to a wall and supported by a thin cable attached 2.0 m from the free end of the beam (Figure 1). The beam is supported at an angle of 30.0° above the horizontal.
Q1: In the below drawings, three unbalanced masses and related details are provided. Please answer the following questions. a) a balancing mass is to be located at rp = 50 mm, then what would be the balancing m1 m1 650 mm 200 mm m2 mass (m,) and its angular position (Op) (Please use the r2 m2 A graphical method) r3 m3 15 m3 b) If the system is not balanced what would be the reaction forces at A and B. (FA, FB=?) n = 150 rpm r; = 30 mm m, = 1 kg r2 = 20 mm 40 тm 13= m, =3 kg m; = 2 kg k = please choose an appropriate scaling factor yourself SHOT ON MI 6 MI DUAL CAMERA