The tube shown is filled with mercury. Calculate the force applied to the piston. The piston is circular with a diameter of D. Consider the Pmercury = 13550 kg/m³ and g=9.81 m/s². Assuming D-60 mm, d=20 mm, H=250 mm and h=30 mm. F= N F H

The tube shown is filled with mercury. Calculate the force applied to the piston. The piston is circular with a diameter of D. Consider the Pmercury = 13550 kg/m³ and g=9.81 m/s². Assuming D-60 mm, d=20 mm, H=250 mm and h=30 mm. F= N F H

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: KN 4m 上 4m 100 t Kat 200

Q: What is Shape Correction Factors For Alpan (1964) Method ?

A: Alpan method (1964) It is based primarily on peck and Terzaghi method (1948). It evaluates the…

Q: Make a checklist of activities during constrution

A: Here we have to. Make a checklist of activities during construction . Checklist is a set of…

Q: SITUATION 3. a) The base and altitude of a triangle lot were measured to have certain probable…

A: a) The base of a triangle, B = 314.60±0.16 The altitude of the triangle, H = 92.60±0.14 To…

Q: 1. With the given profile level notes, STA BM₂ 0 +00 +10 TP₁ 0 +22 + 30.5 +34.2 +39.3 + 42.5 TP₂ 0…

A: To find the Elevation at BMb and to plot the profile

Q: Construct a dot plot for the asphalt data30 75 79 80 80 105 126 138 149 179 179 191 223 232 232 236…

A: Dot plot is used to represent a quantitative data and each dot in the plot represents a value. For…

Q: Convert the following W (a) 53° 55' (b) 45' 175° (c) 222° 35' (d) 305° 55'

Q: will rate immediately pls answer asap wc of the ff gives the deflection at point C

Q: detemine the x and y

A: answer = 4.03 in explanation is given in below step

Q: How is measuring DBH with a biltmore stick different than measuring DBH with a D-tape?

Q: Determine cleflection a=2.5 at b.) Determine cleflection at b=0.4 C) Determine the rotation at c=1 a…

A: Given:Required:Note: As per bartleby guidelines, only first 3 subparts among multiple subparts need…

Q: What is Uniformly loaded rectangular area at the surface ?

A: The external load coming from soil, water pores form the extra incremental stress.

Q: help me plot the horizontal and vertical distance using free hand

Q: FIND PA IN zPa AND VA IN

Q: To control the elevation of a building, contractors must use or establish one or more benchmarks…

A: A differential leveling between station BMA to station BMC is given, with the RL of station BMA…

Q: Find qu Via Terzaghi's equeatioms: JE ア-132 m C =15 ka/m A=20° %3D D=3 m CirCular Shape

A: Foundation is the last supporting part of the structure known as substructure. Footing/foundation is…

Q: Define Normalized CPT Parameters

A: Cone penetration testing (CPT) is used to identify the soil type. In this test a cone penetrometer…

Q: Dist. AB 586.23 BC 462.31 CA 724.26 A Brg. N32-07-55E $54-21-37E $71-42-10W Lat. N32°07'55"E 586.23…

A: Given: Line Distance Bearing AB 586.23 N32o07'55"E BC 462.31 S54o21'37"E CA 724.26…

Q: An 8m steel tape was purchased and advertised as follows: Standard temperature : 24°C Standard Pull…

Q: Explain the layout of dilatometer test?

A: General layout of dilatometer test:

Q: Briefly explain why should blank determination be performed.

Q: A surveyor made 4 different routes of level from Point A to Point B. The elevation at A is 250 m and…

A: Most probable value means the mean value of given data . Given Elevation of point A = 250m Point A…

Q: The cross section at station 2+60 has a cut area of 9 ft² and a fill area of 4 ft² and the cross…

A: Given that, Cut Area of cross-section at station 2+60, A2+60=9ft² Cut Area of cross-section at…

Q: Identify and describe the following surface analysis techniques AES, AFM, EDS, FIB, FTIR, SEM, TEM,…

A: Atomic Force Microscopy (AFM) Atomic Force Microscopy (AFM) is an analysis that quantifies surface…

Q: . Enlist major three sources of errors in

A: Three major sources of errors in surveying are: 1. Instrumental 2. Personal 3. Natural

Q: Table Q2(b). Two-peg test booking BS FS Height of Collimation (m) Reduced Level (m) Remark Distance,…

Q: Determine the force and moment reactions at A for the beam which is subjected to the load…

Q: C. COMPUTATIONS: 1. Computing Stadia Intercept (S) and Stadia Interval Factor (K). a.) Stadia…

A: Given, Stadia Intercept= Upper Rod reading- Lower Rod reading Stadia Interval(K)= DistanceStadia…

Q: Explain limitations of use seismic refraction method for determining subsurface conditions.

A: Seismic Refraction: Seismic refraction maps contrasts in unstable speed – the speed at that unstable…

Q: 202 To determine the distance between two points P and Q and elevation of Q, following observation…

A: H=1.280m P=+4025'20" Staff reading=1.545,1.905,2.265 RL of P=123.265m To find:- the unknown…

Q: Define the importance of Dilatometer Test ?

A: The Dilatometer is a precision instrument used to calculate the volume change caused in the soil…

Q: Amplitude do + Wn

A: Use the following data.

Q: error in the measured interior

A: Given the measured values at Stations A,B,C,D of a quadrilateral.

Q: Prob.59. The following readings were observed with a dumpy level 0.795, 1.535, 2.855, 3.125, 0.945,…

A: R.L of BM = 608.4 m Chainage point (C.P) = after 4 and 8 reading

Q: Describe Correction factor for field SPT values.

A: The field 'N' value must be corrected before the SPT values are used in design charts and empirical…

Q: From the top of a 20-m high bra surveyor measured the angle of depression to the base of another…

Q: Compute the value of Ely at midspan between supports of the overhanging beam shown. 1000 lb 400…

Q: 7.321 meter as yards

Q: The readings (2.312, 1.185, -2.365, 0.195, 0.885, 1.345, 0.905) were taken with a level. The…

A: point back bearing fore bearing height of instrument elevation of point remark 100 BM…

Q: 4. Complete the following set of profile level notes and show the customary arithmetic check. STA BS…

A: solution (4) we have HI = Elevation + BS =Elevation + BS- FS Elevation = last elevation +…

Q: I need complete solution with diagram The R.L of the point A which is on the floor is 100m &…

Q: Module 03- Coursework Activity 03 Complete the Differential Leveling Notes by providing data to the…

Q: Nice, thanks. But where that 10 kN/m2 come

Question

Ans is 82.7 ,Show complete work

The tube shown is filled with mercury. Calculate the force applied to the piston.
The piston is circular with a diameter of D.
Consider the Pmercury = 13550 kg/m³ and g=9.81 m/s².
Assuming D-60 mm, d=20 mm, H=250 mm and h=30 mm.
F=
N
F
H

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: State of given data

VIEW

Step 2: Calculation of force

VIEW

Solution

VIEW

Step by step

Solved in 3 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

5:19 Three Level section A series leveling had been down along the center line of the road the distance between each two points (50m).The road must be started with the same ground level at first point and ending with the same ground level at last point with a uniform .slope. Calculate the slope of the Grad B.S I.S F.S Rise Fill R.L Grad 1.143 20 0.622 19.378 0.801 18.577 1.254 17.323 0.872 16.451 1.765 2.566 1.390 3.820 2.262 0.664 1.598 18.049 3.722 0.433 0.231 18.28 2.886 0.836 19.116 1.618 1.268 20.384 0.616 1.002 21.386 3.08*10-3 - 3.08*10-3 3.08*10 3 3.08*10-2 docs.google.coma EE
QUESTION 4 Table Q4 shows the booking of levelling fieldwork conducted during light rain. It was later found out that some of the readings are illegible due to the rain water. Complete the booking and perform all checks. Table Q4 BS IS FS HPC RL Remarks ? 20.662 18.569 TBM 1 RL 18.569 2.010 ? ? 18.645 3.467 0.418 20.244 C (CP) 3.053 ? D E TBM 2 RL 22.968 1.467 22.243 22.959 !! IMPORTANT ! SAVE THIS QUESTION PAPER (SHADED AREA) IN PDF AND SUBMIT IT TO THE E-LEARNING WEBSITE
3) The following table contains a set of measured levels for an open traverse Station CP1 (BM) 1a 1b CP2 2a 26 CP3 BS IS FS 1.430 3.370 2.010 1.010 2.980 1.410 0.400 0.670 RL 277.650 Find the RL values and do a checking i) use RISE and Fall Method ii) use Method of Height of Plane of Collimation<
Show complete solution pls
3.8 sq ft=___ sq in.
Correct answer is 9,872.198 kN. No other answer thanks
Determine: Use 3 decimals a) The width of the base b) The value of cut at station B if it has an area of 16.82 sq.m. b) The Volume of A and B with prismoidal correction (use end area method)
Petermine atrero Area = lo mm2 =225 KN %3D Farce ఇపక kN-
SITUATION 3. a) The base and altitude of a triangle lot were measured to have certain probable errors of 314.60 0.16 and 92.60 = 0.14, compute the probable error of the resulting computation. (3- b) The following sides of a rectangle and its probable errors are 120.40 0.04 and 360.50 ± 0.08 respectively. Compute the probable errors of the sum of the sides (perimeter) of rectangle. (3r c) The probable error of the mean of 6 observation is 0.043 and the most probable value of the measurement is 860 m compute the relative precision. C
QUESTION 4 Table Q4 shows the booking of levelling fieldwork conducted during light rain. It was later found out that some of the readings are illegible due to the rain water. Complete the booking and perform all checks. Table Q4 BS IS FS HPC RL Remarks 19.245 17.155 TBM 1 RL 17.155 2.010 A 17.169 3.431 0.461 18.784 с (СР) 3.079 D 1.471 20.744 E ? 21.455 ТВМ 2 RL 21.459
PAGE:. DATE :.. A rectangular lot steei tape which was later found to 5 mm too short. The recorded dimensions was mearured uring a be 121.5m long by 92:5m wide. What ir the Were error in the area
Q1/ Calculate the area of the following offsets measured in the field at equal intervals of 10 Offset hl Length 10.76 19.83 (m) Calculate the area using: 1. Trapezoidal Method 2. Simpson's method h3 h4 h5 20.24 18.59 16.76 h8 h9 h10 h6 h7 17.68 17.68 17.37 16.76 17.68