The T- beam used in a heavy storage warehouse is made of concrete having a specific weight of 125 lb/ft3. Determine the dead load per foot length of beam, and the live load on the top of the beam per foot length of beam. Neglect the weight of the steel reinforcement. (heavy storage warehouse live load = 250 lb/ft2) The T- beam used in a heavy storagewarehouse is made of concrete having aspecific weight of 125 lb/ft³. Determine thedead load per foot length of beam, and thelive load on the top of the beam per footlength of beam. Neglect the weight of thesteel reinforcement. (heavy storagewarehouse live load = 250 lb/ft?) :36 in.6 in.8 in.36 in.10 in.-12 in. -

Answered: Image /qna-images/answer/bc6e8262-2579-450f-9bc1-a6c709502782.jpg

The T- beam used in a heavy storage warehouse is made of concrete having a specific weight of 125 lb/ft³. Determine the dead load per foot length of beam, and the live load on the top of the beam per foot length of beam. Neglect the weight of the steel reinforcement. (heavy storage warehouse live load = 250 lb/ft?) : 36 in. 6 in. 8 in. 36 in. 10 in. -12 in.

The T- beam used in a heavy storage warehouse is made of concrete having a specific weight of 125 lb/ft³. Determine the dead load per foot length of beam, and the live load on the top of the beam per foot length of beam. Neglect the weight of the steel reinforcement. (heavy storage warehouse live load = 250 lb/ft?) : 36 in. 6 in. 8 in. 36 in. 10 in. -12 in.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

= ======= == Q2- The architectural engineer proposed a width of 350 mm and a height of 750 mm for a cantilever beam shown below, as you a design engineer ,design this beam according to ACI-14 requirements and assume in your solution that: Mu 1300 kN.m fc 21 MPa and fy 420 MPa Bar diameter of 32mm for longitudinal reinforcement. Bar diameter of 12 mm for stirrups. Two layers of reinforcement for both tension and compression zone. ⚫Use bundle bars when it is possible. 350mm
1. It is a method of applying pre-compression to control the stresses resulting due to external loads below the neutral axis of the beam. a. Prestressed Concrete b. Pre-Compression c. Pre-Tension d. Post Tension 2. In this method the concrete is prestressed with tendons before it is placing in position a. b. Prestressed c. Pre-Tensioning d. Post-Tensioning e. None of the above 3. In this method prestressing is done after the concrete attains its strength a. Prestressed Concrete b. Pre-Tensioning c. Post Tensioning d. None of the above 4. A rectangular concrete beam of 250 mm wide and 600 mm deep is prestressed by means of fours 10 mm diameter high tensile bars located at 200 mm from the soffit of the beam. If the effective stress in the wires is 500 N/mm2. What is the maximum bending moment that can be applied to the section without causing tension at soffit of the beam?? a. O b. 24.5 kN.m c. 26.5 kN.m d. 31.5 kN.m e. 38.5 kN.m
In the figure below, find the value of uniform load w (kN/m) that can be applied on the composite beam if the maximum stresses in steel and timber are 48MPa and 3.2MPA, respectively. Est=195GPa,Etimber=13GPA 120mm W Steel 10mm Timber 300mm 2m 4m 2m 250mm Steel 10mm 120mm
Find the safest value of load "P" for the beam loaded shown. fc'=35MPA, Use GRADE 420 steel bar and n=10 The answer is kN. Assume unit weight of concrete = 24kn/cu.m. 200 3 m 1 m toort twit 3P 70 200 2-20 mm O 330 3. BEAM 4-32 mm Ø 300 100 DIMENSIONS ARE IN "mm"
4. An interior reinforced concrete slab has to be designed to support a live load and a dead load in addition to its own weight based on the following specifications: The slab is one-way and simply supported with a span of 12 ft. The live load on the slab is 200 psf. The dead load on the slab is 100 psf. Your design will use concrete compressive strength fe= 3000 psi and steel yield strength of fy = 40,000 psi
Hello, please solve the question about reinforced concrete from the sixth and seventh chapters of the third civil stage
1/ Calculate maximum deflection of the beams (This was solve it) 2/ Check the suitability of the section assuming the code limitation of L/240. 3/ If maximum deflection doesn’t meet the code requirement, propose your solution
Unit for Concrete a. Pieces b. Sack c. Cubic Meters d. All of the above
using the table below, answer the question
Try
Please answer with each steps.