A unreinforced concrete beam is 6in wide and 12 in deep and has a point load P at the third points of the span. How large can the point load P be before the beam cracks if the f't = 400 psi? 8ft 50 lbs 100 lbs 400 lbs 600 lbs 8ft P 8ft

A unreinforced concrete beam is 6in wide and 12 in deep and has a point load P at the third points of the span. How large can the point load P be before the beam cracks if the f't = 400 psi? 8ft 50 lbs 100 lbs 400 lbs 600 lbs 8ft P 8ft

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Situation: A beam has a width of 300 mm and total depth of 600 mm strength f'c-36 MPa. Steel yield strength fy=415 MPa The section is to be reinforced for tension only and the effective concrete cover is 65 mm. Which of the following most nearly gives the value of our balanced steel ratio? a. 0.00370 b. 0.03456 C. 0.02860 d. 0.03522 Which of the following most nearly gives the value of our balanced distance of the cuter most fiber of compression fiber to our neutral axis? a. 313.256 mm b. 354.68 mm C. 333.333 mm d. 322.435 mm Which of the following most nearly gives the value of our balanced depth of compression block? a. 248.412 mm b. 266.2676 mm C. 301.478 mm d. 281.261 mm
SITUATION. Given: BxH 400 mm x 500 mm As = 6 x 20 mm Ø diameter bars Clear concrete cover to 10 mm diameter ties = 50 mm Concrete fc' = 28 MPa Steel fyl = 415 MPa Steel fyv 275 MPa Ø=0.75 If the column is replaced with a 400mm diameter section and the nominal shear capacity of concrete is 1.20 MPa, which of the following most nearly gives the nominal shear strength (kN) of the concrete, Vc? O260 150 = 260 150
Problem No. 3 A beam 200x450mm is reinforced by 2-32mm diameter rebar. Assume cc-50mm, stirrups-10mm, fc'-21Mpa and fy-415Mpa. Calculate the following. 18. Calculate the strain of the steel reinforcement
6. ESTIMATION OF QUANTITIES OF STEEL & R.C.C. ELEMENTS EPU Example 1: Estimate the Slab reinforcement for the given figure below. All the straight bottom bars are 10mm@400mm c/c. All offset bars 12mm@400mm c/c, All Additional Top bars 12mm@400mm c/c. The slab thickness is 150mm. Assume cover is 25mm & wall thickness20cm 0.45 0.45 3.70 4.70 0.45 0.45 3.70 5.20 3.10 1.60 150
1. A two span beam subjected to shear and flexure only is reinforced as follows: SECTION: TOP BARS @ MIDSPAN: 2-⌀20mm @ FACE OF SUPPORTS: 5-⌀20mm SECTION: BOTTOM BARS @ MIDSPAN: 3-⌀20 mm @ FACE IF SUPPORTS: 2-⌀20 mm Given: Stirrup diameter, ds = 10 mm Concrete f'c = 21 MPa Steel rebar fy = 415 MPa Stirrup fy = 275 MPa Beam size b x h = 270 mm x 450 mm Assume all bars laid out in single layer. Calculate the following: a. Design Moment strength of section at midspan for positive bending = ______ kN·m (nearest whole number)
A RC beam of cross section 220 × 460 mm is subjected to following forces: Factored shear force = 30 kN Factored bending moment = 35 kNm Factored torsional moment = 5 kNm What should be the minimum area of tension steel provided such that there is no need to provide torsional reinforcement. Use M20 grade concrete and Fe415 grade steel. Use the following data for M20 grade concrete. 100 As 0.50 0.75 1.00 1.25 1.50 bd Design shear stress (N/mm²) 0.48 0.56 0.62 0.67 0.72
37 A simply supported beam 300 mm wide, 500 mm deep and spans 5.5 m supports a service super imposed dead load of 8 kN/m and service live load of 7 kN/m. Concrete strength f’c = 21 MPa and steel yield strength fy = 415 MPa. Concrete cover to bar centroid is 70 mm. Determine the required amount of tensile reinforcement in mm^2 as per provisions of NSCP 2015. Write your final answer to the nearest whole number.
Details of a rectangular column are as follows: Column width along the x-axis = 250 mm Column width along the y-axis = 600 mm Reinforcement 8 of 25 mm diameter bars distributed equally along the longer sudes 10 mm diameter ties spced 100 mm on centers. Concrete 28th dat compressive strength, fc' = 20.7 MPa Reinforced steel yield strength, fy = 415 MPa Assume that the compression steel yields. Concrete cover to the centroid of bars 70 mm Determine the nominal balanced load with eccentricity measure from the y-axis if the depth of the rectangular concrete compressive stress block is 90.66 mm.
FLEXURAL ANALYSIS CONCRETE UNCRACKED Problem: Calculate the uniform load (in addition to the beam weight) which will cause the section to begin to crack if they are used for 28 ft simple span. = 4000 psi , the modulus of rupture f, = 7.5f',, and reinforced concrete weight is 150 lb/ft³. 15" 18" 2 #8 3" 12"-
Given a concrete column that would be required to support loads of Pu=400kips and Mu=50 kip-feet, we will determine the column interaction curve and decide if the column is adequate for this particular application. The column will be a 14”x14” square, tied column with #9 bars at the corners. The center of the reinforcement in each corner is 3” from each of the sides. The f’c of the concrete is 4 ksi and the reinforcement is Grade 60. Determine the maximum compression load that the concrete column can support. Do not include a reduction resistance factor or for any small moment applied to the column. In other words, use the basic strength of the concrete plus the basic strength of the steel.
Load = 3000 lb Q:Find Stresses at: Section A-B & Section D-C "18.0"- "5,5" Plain Concrete: D Compressive Strength : 280 (Psi) "12.0"- "0.5"-
!! Show Complete & Detailed Solution w/ FBD !!The concrete post in the figure, is reinforced axially with four symmetrically placed steel bars, each ofcross-sectional area 750 mm2. The moduli of elasticity are 200 GPa for steel and 14 GPa for concrete. A 2000-kN axial load is applied. Compute the:a. axial force in concrete;b. axial force in the steel bars;c. stress in the concrete;d. stress in the steel bars;e. deformation of the concrete post.