The stresses at the bottom surface of a fuel tank [part (a) of the figure] are ax 50 MPa, ay 8 MPa, and zxy 6.5 MPa [bart (b) of the figure]. A 195-T6 aluminum casting shows Sut-36 kpsi, Suc=35 kpsi. For the given plane stress state, a) use Mohr-Coulomb theory and determine the factor of safety. Ţ 8 MPa 6.5 MPa 50 MPa

The stresses at the bottom surface of a fuel tank [part (a) of the figure] are ax 50 MPa, ay 8 MPa, and zxy 6.5 MPa [bart (b) of the figure]. A 195-T6 aluminum casting shows Sut-36 kpsi, Suc=35 kpsi. For the given plane stress state, a) use Mohr-Coulomb theory and determine the factor of safety. Ţ 8 MPa 6.5 MPa 50 MPa

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

K=17 so 107 MPa strength of material question.
= 73,0 GPa As = 1500 mm ² ) rod and a brass (Eg = 100 G+Pa t are stress-free and and AB = 2000mm²) rod. At 25°C, The rods of 1.00mm exosts between them. дар expansion If the coefficrear of thermal as of = 14 [106 m/m'c] that of brass a f = 11 [10° ⁰ m/m²c], A Temperature increased to 350°C.. a A Stech | E₁ kuhat is intermidate Temperature (umt°C) that system must be taken to in order to clase the of 1.00mm? A it Steel 1.00mm → K B Brass 1.50000m. for steal is taken as and 1.0 ME the gap 15
Q1B
A circular column is made of concrete [Ec = 4.2(103)ksi] while being reinforced with six steel rods [Est = 29 (103 )ksi]. It is acted upon by an axial force of 30 kip as shown in the figure to the right. Each rod has a diameter of 0.85 in. c) Stress in each steel rod, σst = ____________________ ksi d) Stress in the concrete, σc = ____________________ ksi
answer as soon as possible
A circular column is made of concrete [Ec = 4.2(103)ksi] while being reinforced with six steel rods [Est = 29 (103)ksi]. It is acted uponby an axial force of 30 kip as shown in the figure to the right. Each rod has a diameter of 0.85 in. Find the forces in each steel rod, concrete, stress in each steel rod and concrete.
Question 1 The cube in Figure Ql made of 200 mm sides of a certain material is subjected to a volumetric stress of 50 N/mm?. Determine the change in its volume if the Bulk modulus of the material is 100x10° N/mm?. 200 mm Figure Q1: Cube subjected to volumetric stress
Need Help With This Question
2.3 (A). What will be the stress induced in a steel bar when it is heated from 15°C to 60°C, all expansion being prevented? For mild steel, E = 210 GN/m² and a = 11 x 10-6 [104 MN/m²] per °C.
(2) The strength condition of composition of bending and torsion is _M₂ _ √ M² + (ar)² ≤ [0_1b] W 0.1d³ Please write down the meaning of the following symbols in the formula. de 2 M 3 T (4) a [0-1b]
We have a grounded 2 cm in diameter steel shaft which is 10 cm in length connected to a rigid surface. This shaft is subject to the stresses at the tip point as given below; Tmean = 100 Nm, Talternating= 50 Nm, • Mmean = 30 Nm, Malternating = 40 Nm, Fmean = 4 kN, Faltemating= 6 kN. This shaft has minimum properties of Sy = 800 Mpa and Sut = 1000 Mpa. Assume; Kf for bending=1.5, Kf for tension = 1.4, and Kfs for torsion = 1.8. Using Modified Goodman criterion what can you say about the shaft? Does it have a limited life, if yes, how many cycles?
please help me with this