= 73,0 GPa As = 1500 mm ² ) rod and a brass (Eg = 100 G+Patare stress-free andand AB = 2000mm²) rod. At 25°C, The rodsof1.00mm exosts between them.дарexpansionIf the coefficrear of thermalasof= 14 [106 m/m'c] that of brass a f = 11 [10° ⁰ m/m²c],ATemperature increased to 350°C..aA Stech | E₁kuhat is intermidate Temperature (umt°C) that systemmust be taken to in order to clase theof 1.00mm?AitSteel1.00mm→ K BBrass1.50000m.for steal is taken asand1.0 MEthe gap15

GivenEs=73 GPaAs=1500mm2EB=100GPaAB=2000 mm2T1=25oC∆=1mmαs=14×10-6 m/moCαb=11×10-6 m/moC

= :73.0 GPa Ag = 1500 mm²) rod and a brass (EB = 100 t and AB= 2000mm ²2² ) rod. At 25°C, the rods are stress-free of 100 mm exosts between them. Astech Es a дар If the coefficreur of thermal expansion as for steal is 19 = 14 [10`6 m/m'c] that of brass og = 11 [ 10% m/m²]

= :73.0 GPa Ag = 1500 mm²) rod and a brass (EB = 100 t and AB= 2000mm ²2² ) rod. At 25°C, the rods are stress-free of 100 mm exosts between them. Astech Es a дар If the coefficreur of thermal expansion as for steal is 19 = 14 [10`6 m/m'c] that of brass og = 11 [ 10% m/m²]

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1.6-7 A wire of length L = 2.5 m and diameter d = 1.6 mm is stretched by tensile forces P = 600 N. The wire is made of a copper alloy having a stress- strain relationship that may be described mathemat- ically by 124,020ɛ 0 s8s 0.03 (o = MPa) 1+ 300ɛ in which e is nondimensional and o has units of MPa. (a) Construct a stress-strain diagram for the material. (b) Determine the elongation of the wire due to the forces P. (c) If the forces are removed, what is the permanent set of the bar? (d) If the forces are applied again, what is the proportional limit?
ERCISE WORKED EXAMPLE A piece of Aluminium of cross sectional area 60 mm is bonded to a piece of steel of CrosS sectional area 120 mm². The lengths of both materiais are the same at 150 mm. The component is then heated through a temperature rise of 100 °C. Take Es = 207 GN/m and EAL = 45 GN/m2 %3D 12 x 10° PC and aAL = 27 x 10° °C. (a) Find the stresses induced in the steel and aluminium. (b) Find the extension of the compound bar. %3D as d bar:
We have a grounded 2 cm in diameter steel shaft which is 10 cm in length connected to a rigid surface. This shaft is subject to the stresses at the tip point as given below; • Tmean = 100 Nm, Talternating= 50 Nm, • Mmean = 30 Nm, Malternating= 40 Nm, Fmean = 4 kN, Falternating = 6 kN. This shaft has minimum properties of Sy = 800 Mpa and Sut = 1000 Mpa. Assume; Kf for bending=D1.5, Kf for tension = 1.4, and Kfs for torsion = 1.8. Using Modified Goodman criterion what can you say about the shaft? a) Does it have an infinite life?
Q2. Show that = Cr2(a - 0 + sin 0 cos 0 – tan a cos? 0) is a permissible Airy function for the tapered cantilever of uniform thickness, shown in Figure 2, and derive expressions for the corresponding stresses or, 0g and tre. Also, find the %3D value of the radial stress at 0-0° when a=30°. w/ unit length Figure 2
material mechanics
FN = 50
H.W.6: A hollow circular cold-rolled bronze [G, = 6,500 ksi] tube (1) with an outside diameter of 1.75 in. and an inside diam- eter of 1.25 in. is securely bonded to a solid 1.25-in.-diameter cold-rolled stainless steel [G2 = 12,500 ksi] core (2) as shown in Figure and the allowable shear stress of core (2) is 60 ksi. Determine . The allowable shear stress of tube (1) is 27 ksi, (a) the allowable torque T that can be applied to the tube-and- core assembly. (b) the corresponding torques produced in tube (1) and core (2). (c) the angle of twist produced in a 10-in. length of the assembly by the allowable torque T. (1) T TA FIGURE
By the equipment as shown in the figure, temperature can be measured. The bar AB and CD are made from aluminum and titanium. The coefficients of thermal expansion are 23.6x106 1/K and 8.2x10-6 1/k. Obtain the relationship between the temperature and the vertical displacement at the point E. 6 mm 72 mm 36 mm D
A circular column is made of concrete [Ec = 4.2(103)ksi] while being reinforced with six steel rods [Est = 29 (103 )ksi]. It is acted upon by an axial force of 30 kip as shown in the figure to the right. Each rod has a diameter of 0.85 in. c) Stress in each steel rod, σst = ____________________ ksi d) Stress in the concrete, σc = ____________________ ksi
answer as soon as possible
Pls box ur answer thx u
Q1// A hollow shaft of 10mm inside diameter and 5mm thick and 2m long extends by 0.5 cm under a tensile load (P) .find 1- the load P if E=2.10° N/cm? 2-the tensile stress in the shaft.