The stress state in which the only nonzero stress components are a singlepair of shear stresses is called simple shear, where0 0LO 0 02.1) Find the principal values and principal directions on this stress state.2.2) Find the maximum shear stress and the planes on which it acts.

Answered: Image /qna-images/answer/8971ca33-5a5e-402b-b730-203862b0ed8d.jpg

The stress state in which the only nonzero stress components are a single pair of shear stresses is called simple shear, where T. TO0 0 0 0 2.1) Find the principal values and principal directions on this stress state. 2.2) Find the maximum shear stress and the planes on which it acts.

The stress state in which the only nonzero stress components are a single pair of shear stresses is called simple shear, where T. TO0 0 0 0 2.1) Find the principal values and principal directions on this stress state. 2.2) Find the maximum shear stress and the planes on which it acts.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The stresses acting on a very small member are shown in the figure.a) The greatest shear stress theoryb) Find the coefficients of safety for flow, taking into account the theory of maximum strain energy. (yield stress 900 MPa)
Q1. If the yield stress (oy) of a material is 375MPa, determine whether yield is predicted for the stresses acting on both the elements shown below using: P₁=-215 RF 330 (a) Tresca Criterion (b) Von Mises Criterion Q = 200 Element A Note: your values for P (vertical load on Element A) should be negative (i.e. corresponding to a compressive vertical load). Element B S=90
A bar with varying cross section is subjected to various forces as shown below. Compute: a) Stresses in each section b) strain in each section c) total extension of the bar. Take E = 2.1x105 N/mm² P1=17 kN P3=38 kN P4-21 KN 400 mm P₁+ A 1000 mm B 800 mm² P2 P3+ 1500 mm 600 mm² 800 mm P4
For the given load, find the value of the stress amplitude and stress ratio respectively,
2. In one specific point in a structure, the stress state is as pictured on the differential element. Calculate a) Principal stresses and their angle of orientation b) Absolute maximum shear stress.
The state of plane strain at a point is represented by the following components: 6, = 5o010-).e, = -30010). 7,, = 240(10-6) a) Draw Mohr's circle to represent this state of strain. b) Use Mohrs circle to obtain the principal strains and principal plane. c) Draw a sketch to illustrate the principal strains and plane.
Determine final dimension of the block in mm
A bar with varying cross section is subjected to various forces as shown below. Compute: a) Stresses in each section b) strain in each section c) total extension of the bar. Take E = 2.1x105 N/mm² 400 mm² P1=10kN A 1000 mm B 800 mm mm² P₂ P3=45KN+ 1500 mm 600 mm² 800 mm → P4-35kN
3. Consider a point in a loaded body subjected to the stress field represented in Fig. 3. Determine the principal stresses and orientation (with respect to the original system) of the maximum principal stress (01) in terms of direction cosines (1, m, n) and angle, 0. Use both formulas and Mohr's circles to solve. 60MPa 50MPa Fig. 3 20MPa 100MPa >X
The maximum principal stress in a material is 6 MPa. If the second invariant of the stress tensor is -4 MPa and the third invariant of the stress tensor is -48 (MPa)' find: (a) The remaining principal stresses (b) The normal and shear stresses on a plane, whose normal direction cosines are 0.6, 0.3 and 0.742 (c) The state of stress existing on the maximum shear plane (d) The unit vectors which define the plane in (c) relative to the principal directions.
Q.2) For the state of stress shown below, determine the orientation and values of principal stresses, the in-plane maximum shear stress, and absolute maximum shear stress using (a) Stress transformation equations (b) Mohr's Circle (c) Sketch the stress block with proper orientation for each case (Principal stress, in-plane maximum shear stress and absolute maximum shear stress). y 40 MPa 80 MPa 25 MPa
hand write asap