The stress at a point is shown on the element. Determine (a) principal stress, (b) maximum in-plane shear stress. Specify the orientation of the element in each case. Find also the (c) the stress in the element on the inclined plane. (See required values in answer sheet format) 50 MPa 25 MPa 45 MPa 45 MPa 35 50 MPa

The stress at a point is shown on the element. Determine (a) principal stress, (b) maximum in-plane shear stress. Specify the orientation of the element in each case. Find also the (c) the stress in the element on the inclined plane. (See required values in answer sheet format) 50 MPa 25 MPa 45 MPa 45 MPa 35 50 MPa

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter1: Introduction

Section: Chapter Questions

Problem 1.5.6P: The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular...

See similar textbooks

Similar questions

The stress at a point is shown on the element. Determine (a) principal stress, (b) maximum in-plane shear stress. Specify the orientation of the element in each case. Find also the (c) the stress in the element if it is inclined 55° counterclockwise. (See required values in answer sheet format) 65 MPa 35 MPa 85 MPa 85 MPa 65 MPa
The failure stress of a homogeneous steel bar having a diameter of 10 mm is 250 MPa. Using a factor of safety of 2.0, calculate the maximum load in N that the bar can support. A 12500*pi В) 6250*pi C) 3125*pi 1563*pi
For the state of stress shown, determine (a) the principal stresses, (b) the maximum in-shear stress. Sketch such stresses in a two- element format. 60 MPa 90 MPa Lx 30 MPa
Problem II. An exhaust gas piping fabricated as shown is subjected to a bending moment, an internal pressure, and a torque. In points A and B, the following stresses occur due to the loading: o 63.5 MPa, B=127 MPa, = 127 MPa A.B A.B a. Determine Gmin, omax, and its direction (in degrees) from x-axis at point A. b. Determine omin, omax, and its direction (in degrees) from x-axis at point B. 1 B d O A x
PROBLEM 1 Determine the load that can be applied at the end of the rigid bar if the stress in either spring shown in the figure shall not exceed 200MPA. Spring 1 Spring 2 n 20 30 d 10mm 20mm 150mm 120mm 83GPA 35GPA 2m 2M 2M www
An aluminum rod is rigidly attached between a steel rod and a bronze as shown. Axial loads are applied at the positions indicated. Find the stress of each rod in MPa. Steel Aluminum Bronze A- 500mm A = 400mm? A- 200mm 40KN 10KN 20KN 1.5m 2.5m 2.0m Determine the change in length of steel rod having a length of 800mm and a diameter of 6.5mm. The rod is subjected to a force P equal to 110KN. Young's Modulus is 200GPA Compute normal strain of the rod
Problem II. An exhaust gas piping fabricated as shown is subjected to a bending moment, an internal A,B pressure, and a torque. In points A and B, the following stresses occur due to the loading: o 63.5 MPa, B=127 MPa, T = 127 MPa = a. Determine omin, omax, and its direction (in degrees) from x-axis at point A. b. Determine omin, omax, and its direction (in degrees) from x-axis at point B. 1 B x COO O A
200 mm diameter rod is subjected to loads as shown. Determine the state of stress at points A and B. Show your results on an infinitesimally small square plane (please use the ones drawn below, which helps you in directions). 8 m 600 N 10 m 400 N 700 N B Txy Ox A
Question 5 [Similar to Problem 9-17] Consider the following figure showing state of stress at a given point in a structural or machine element. Identify normal and shear stresses acting on the element. Find principal stresses. Show the orientation of the element on which the principal stresses act. Find maximum in-plane shear stresses. Find associated normal stresses. Show the orientation of the element on which these stresses act. 150 MPa 50 MPa 100 MPa Moch onios of Motoriols
Part 2 * Your answer is incorrect. The z-component of momemt M will cause compression at A and B, and tension at C and D. The y-component of moment M will cause compression at A and D, and tension at B and C. The maximum tensile bending stress will occur at point C. Calculate the magnitude of the largest bending moment that can be applied so that the stress at corner C does not exceed 205 MPa. Answer: M- eTextbook and Media Save for Later Part 3 8.31E1 Answer: M-i The z-component of moment M will cause compression at A and B, and tension at C and D. The y-component of moment M will cause compression at A and D, and tension at B and C. The maximum compressive bending stress will occur at point A. Calculate the magnitude of the largest bending moment that can be applied so that the stress at corner A does not exceed 205 MPa. eTextbook and Media Save for Later Part 4 kN-m * Your answer is incorrect. kN-m Submit Answer Determine the maximum bending moment that can be applied to this cross…
The figure (all dimension are in mm) below shows an I-section of the beam. The shear stress at point P (very close to the bottom of the flange) is 12 MPa. The stress at point Q In the web (very close to the flange) is: N'-. 100- P Q 201 100- T 20 81484 80 20 40 --N (a) Indeterminable due to incomplete data (6) 60 MPa (c) 18 MPa (d) 12 MPa 068
Situation 2 For the assembly shown, determine the stress in each of the two vertical rods if the temperature rises 40°C after the load P=50 KN is applied. Neglect the deformation and the mass of the horizontal bar AB. Compute the vertical movement under the load. Steel Aluminum E=200 GPa E=70 GPa L-4m A=300 mm? a-11.7x10*/°C L-3m A=900 mm a=23x10“ /°C 3 m 3 m 3 m Situation 3